EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3XART73 Whirlpool Refrigerator - Instructions

All Instructions for the 3XART73
91 - 105 of 1083

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cracked Crisper Drawer
13 of 15 people found this instruction helpful.
  • Jennifer from Salvisa, KY
  • Really Easy
  • Less than 15 mins
This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.
Was this helpful?
Thank you for voting!
The Ice maker would not work.
22 of 42 people found this instruction helpful.
  • Jerry from Boulder, CO
  • Easy
  • 1- 2 hours
  • Screw drivers
We rolled the refrigerator out away from the wall and it was obvious where the break was located. We took out the old water spout for the ice maker and replaced the tube and the tubing from the solenoid. We turned it on and soon we had water dripping everywhere. We unloaded and defrosted the freezer which got all of the remaining ice th at was stuck in there. We put everything back together. I read in some instructions in the manual that it might take 24 hours for the ice maker to reprogram itself and start producing ice. I was only about 12 hours and we had ice again and everything worked well. You really do not have to disconnect the water from the main line, the solinoid controls that part of operation and turns the water off until the ice trays are free and clear.

JLB
Was this helpful?
Thank you for voting!
spout on water dispenser broken
13 of 15 people found this instruction helpful.
  • JIM from SACRAMENTO, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Cut off old nozzle. Tried electricians tape to join the old and new tubing for fishing, but tube with tape on it, wouldn't fit through hole in hinge at bottom of door. Fished nylon twine through new tube then old tube from dispenser end and was able to feed old tube out and new tube in. Fast and easy. Took more time to clean all the d ust and dirt I found down under, than to make the repair.
Was this helpful?
Thank you for voting!
Broken cup water fill on ice maker
13 of 15 people found this instruction helpful.
  • Matthew from Aurora, CO
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt
Was this helpful?
Thank you for voting!
Auger drum broke
15 of 22 people found this instruction helpful.
  • Michael from Deer Park, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Wrench (Adjustable)
Very easy. Your online video was agreat help.
Was this helpful?
Thank you for voting!
Water would not come out of the dispenser.
11 of 11 people found this instruction helpful.
  • Ralph from Saint Petersburg, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed catch tray and then removed two screws that are underneath. I left the control panel hanging from its wires, then removed the two screws from the control bracket.
A word of caution before next step: You need to remove the two micro switches on the left and right. While trying to remove one, it split apart and the pieces fell out. I was able to put it back together and it worked fine. So be careful with the micro switches.
Continue tranferring wires and switches to the new bracket and reassemble in the opposite order.
An easy repair.
Was this helpful?
Thank you for voting!
The ice despenser in the door has never worked properly
15 of 23 people found this instruction helpful.
  • David from Getzville, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver
Replaced the ice bucket (old one was cracked) the auger, auger coupling and auger drum. The new parts had been redesigned to replace the orginal auger helix and auger sleeve which had been replace two times and never seemed to last more than a few weeks. The new parts work great and we have as much ice available as we need. The replacemen t was stright forward but I do reccomend that you make a simple drawing of the ice crusher blade and washer locations as you dissassemble them to aid in reassembly.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Cover Pan Crisper(bottom glass shelf and frame) were broken
13 of 18 people found this instruction helpful.
  • anthony from ormond beach, FL
  • Really Easy
  • Less than 15 mins
New part slipped right into the studs and fit perfectly
Was this helpful?
Thank you for voting!
the ice dispenser, micro switch control bracket broke and the ice was not dispensing
11 of 12 people found this instruction helpful.
  • Nelson from East Orange, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the screws that held the control breaket. Then I removed (2) micro switches, and for a cable tie, I slide the old control bracket out and installed the new one purchased from your store. 5 minutes worth of work. THAT IT!!! It was very, very, simple the repair
Was this helpful?
Thank you for voting!
'Frig door made a popping sound when opening and closing.
11 of 12 people found this instruction helpful.
  • Lance from Richardson, TX
  • Really Easy
  • 15 - 30 mins
  • Socket set
Removed upper hinge cover and hinge, lifted door from lower hinge socket, removed lower cam from 'frig hinge, and replaced with new. I had a helper hold the 'frig door while I removed old upper cam, and replaced with new. Piece of cake and works like new! This must be a design problem..
Was this helpful?
Thank you for voting!
ice maker and water dispenser would not work due to switch clamps being broken off the control plate
13 of 18 people found this instruction helpful.
  • scott from huntersville, NC
  • Easy
  • 15 - 30 mins
  • Screw drivers
remove the front cover. everything else is a quick disconnect type of connection. Nothing to it! I would remove the cover and check these connections anytime the dispenser does not work. Look for broken or disconnected switches. This reapir took me a couple of minutes whereas the repair guy wanted almost 200 bucks to do this job. Parts ra n around 30 with shipping.
Was this helpful?
Thank you for voting!
The piece that covered the light at the back of the fridge burnt a hole in the cover.
11 of 13 people found this instruction helpful.
  • Jennifer from Islandia, NY
  • Really Easy
  • Less than 15 mins
First I removed the cover...and then I slid the new piece in. It looks great and so easy a caveman could do it...lol
Was this helpful?
Thank you for voting!
Ice Door Leaking
13 of 19 people found this instruction helpful.
  • Steve from Metairie, LA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Remove the unit cover by unsnapping from the bottom. Remove the face plate on the switches. The ice door simply snaps off the closing mechanism. The problem I have is that the original door included a heat trace element (keeps the back of the door warm to limit condensation). The new part was simply a new seal. I clipped the leads to the het trace (turn off the fridge before you do that) and put in the new door. When the heat ids on in the house there is no problem with condensation but on warmer days its pretty bad. I cannot find a replacement part with the heating element and have contacted Whirpool. THey haven't responded as of yet.
Was this helpful?
Thank you for voting!
Broken gooseneck on fill tube
10 of 11 people found this instruction helpful.
  • Thomas from Brunswick, OH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
The gooseneck on the icemaker fill tube extends out beyond the back cabinet of the refrigerator, and is easily broken. Luckily, this part is a piece of cake to replace. You'll literally spend more time pulling out your fridge and cleaning out behind it then you will replacing this part.

Shut off water supply line, and turn of f ice maker (lift the metal bar in the ice bucket all the way up). Loosen the hose fitting, and remove two screws. Pull out the old tube, and slide the new one in. You may have to wiggle the tube around from the inside to get the alignment correct. Replace screws and fitting. Turn water and ice maker back on, and check for leaks. It really is that easy! It took me longer to type this than to actually replace the part.

Only one potential catch. The instructions warn that you may have to cut the new tube to match the length of the old tube, so make sure you compare the length of the old and new tube. I didn't have to to do anything - the replacement part was the exact same length of the original. If by chance you do need to cut the tube, you'll need small saw of some sort, such as a coping or hack saw.
Was this helpful?
Thank you for voting!
All Instructions for the 3XART73
91 - 105 of 1083