3XART70 Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
part of a freezer support bracket was missing
9 of 10 people
found this instruction helpful.
-
peter from saint augustine, FL
- Really Easy
- Less than 15 mins
I wasn't sure the kit included the part I needed from the pictures, but it did. The part slipped over the flat plastic bracket attached to the right freezer wall and the shelf fit over it. No tools required.
Was this helpful?
Thank you for voting!
leaking water dispenser
12 of 19 people
found this instruction helpful.
-
roxana from dinuba, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
worked great parts were perfect!
Other Parts Used:
Was this helpful?
Thank you for voting!
The refrigerator leaked water every time the ice maker filled.
11 of 16 people
found this instruction helpful.
-
Robert E. from Darien, IL
- A Bit Difficult
- Less than 15 mins
The problem was discovered to be a cracked fill tube head, This part extends behind the refigerator and is VERY vulnerable to breakage when the box is pushed backagainst a wall space! Placing a shim under the vertical part of the fill tube fixed the problem even without replacing it with the new part. So, now I have a spare!
Was this helpful?
Thank you for voting!
There was no light on in refrig area
12 of 19 people
found this instruction helpful.
-
Lori from Chuluota, FL
- Easy
- Less than 15 mins
-
Screw drivers
Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.
But Parts Select is a great place to order from. Thank you.
Was this helpful?
Thank you for voting!
broker door on ice shute
14 of 25 people
found this instruction helpful.
-
John from Willington, DE
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
hardest part was getting up the nerve to pull front cover because it is plastic afraid i would brake it pull from bottom and lift up one screw holds old door inplace uplug electric new door doesn't have electric that it.
Was this helpful?
Thank you for voting!
Worn out door chute
14 of 25 people
found this instruction helpful.
-
Murali from Rochester, MN
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Pry open the front dispenser outer cover. Remove a screw holding ice door dispenser unit, remove old door chute, remove and place coil kind of stuff (connecting to panel) old chute to new one and reinstall.
Was this helpful?
Thank you for voting!
THERMOSTAT
9 of 10 people
found this instruction helpful.
-
dominique from COMPTON, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I followed your instructions , the only thing that was left out was that the freezer has a drain hole that had to be thawed out with a hair dryer,till the water went to the drain pan underneath the ref. your instruction were through enough, that's why I purchased the part from your company, I installed the part 2 days ago and its working
... Read more
like new again 23.00 for the part instead of 1200.00 dollars for another ref. thanks very much. 6 months ago I purchased the relay and compressor starter from your company at that time per your instructions I shook the compressor starter and like a light bulb it had something broke inside,I needed that thanks again oomk
Read less
Was this helpful?
Thank you for voting!
tube got cut and it leaked
9 of 11 people
found this instruction helpful.
-
Robert G. from Kalkaska, MI
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
first I turned off the water supply then I removed screw that was holding the nozzle and pulled out the tube then I pried out the face plate by prying from the bottom with a thin screw driver then I unpluged the wire harness so I could access the black tube guide that the white tube was housed in before it was cut I pushed the new white
... Read more
tube down threw the black tube and out the bottom hinge I replaced the nozzle screw plugged the harness back in replaced the face plate went to the bottom and connected the tube to the other half replaced the bottom molding and turned on the water
Read less
Was this helpful?
Thank you for voting!
The shelf runner broke
10 of 15 people
found this instruction helpful.
-
Andrew F from Media, PA
- Really Easy
- Less than 15 mins
Took out the old one and put in the new one. No tolls required. It did give me the opportunity to clean the back wall of the refrigerator.
Was this helpful?
Thank you for voting!
My drawer had been broken and I needed a new one.
8 of 9 people
found this instruction helpful.
-
Jennifer from Birmingham, AL
- Really Easy
- Less than 15 mins
When I took the pan out of the box, it was not the exact same as the one I had. But it fit perfect. The only hard part was the fact that it looked so good I had to clean the entire fridge side. (Smile)
Was this helpful?
Thank you for voting!
Broken Crisper Frame And Pan
9 of 12 people
found this instruction helpful.
-
Mauricio from National City, CA
- Really Easy
- Less than 15 mins
Jus took me seconds to replace both items. No problem.
Other Parts Used:
Was this helpful?
Thank you for voting!
Worn Down Upper And Lower Cam
8 of 9 people
found this instruction helpful.
-
Jose from Corona, CA
- Easy
- 30 - 60 mins
-
Pliers, Wrench set
Took off refrigerator door from top hinge and lifted off. A little difficulty getting worn out parts off (needed dremel to drill out worn plastic); replaced with new parts, the screw head holding on the part was starting to be worn as well but still worked. If I hadn't got to this repair soon the bottom of the door aluminum would have t
... Read more
otal worn out as it is, it has a deep groove but not noticeable. The new cams also force the door closed tight instead of slightly ajar at times.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Contact in thermostat assembly was burned up, making the freezer irregular and the ice would melt, then freeze into a ball!
9 of 12 people
found this instruction helpful.
-
Jennifer from Schertz, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I took off the front cover with the controls. Pulled out the control knobs, unbolted the assembly (which was identical to my replacement part) and proceded to follow the old thermostat tube to the back of the fridge. The tube should be carefully removed, not pulled on, there's a couple of screws holding it in towards the back. I installe
... Read more
d the new part in reverse of how I took out the original part. I'm very happy with how the fridge has come back to life! It was much cheaper to fix it than to replace.
Read less
Was this helpful?
Thank you for voting!
replacing thermostat did not help
10 of 15 people
found this instruction helpful.
-
John from Rocky River, OH
- Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set
Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiv
... Read more
er boaed. I turn off manually the icemaker, when needed
Read less
Was this helpful?
Thank you for voting!
Chrisper pan support cracked due to overfilling
9 of 13 people
found this instruction helpful.
-
David from Lenexa, KS
- Easy
- Less than 15 mins
removed old shelf support after taking out the glass and support. New part was a perfect fit that was a "shap: to put in.
Was this helpful?
Thank you for voting!