3XART70 Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cover Pan Crisper(bottom glass shelf and frame) were broken
13 of 18 people
found this instruction helpful.
-
anthony from ormond beach, FL
- Really Easy
- Less than 15 mins
New part slipped right into the studs and fit perfectly
Was this helpful?
Thank you for voting!
the ice dispenser, micro switch control bracket broke and the ice was not dispensing
11 of 12 people
found this instruction helpful.
-
Nelson from East Orange, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the screws that held the control breaket. Then I removed (2) micro switches, and for a cable tie, I slide the old control bracket out and installed the new one purchased from your store. 5 minutes worth of work. THAT IT!!! It was very, very, simple the repair
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Ice Door Leaking
13 of 19 people
found this instruction helpful.
-
Steve from Metairie, LA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Remove the unit cover by unsnapping from the bottom. Remove the face plate on the switches. The ice door simply snaps off the closing mechanism. The problem I have is that the original door included a heat trace element (keeps the back of the door warm to limit condensation). The new part was simply a new seal. I clipped the leads to
... Read more
the het trace (turn off the fridge before you do that) and put in the new door. When the heat ids on in the house there is no problem with condensation but on warmer days its pretty bad. I cannot find a replacement part with the heating element and have contacted Whirpool. THey haven't responded as of yet.
Read less
Was this helpful?
Thank you for voting!
refrigerator door was making a popping noise when opening and closing
10 of 10 people
found this instruction helpful.
-
Vincent D from Blackwood, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver
Not being a handyman I found this job realtively easy.I took most of stuff off fridge door, to make door easier to handle. I then undid top hinge door screws, 3 of them, lifted door out., replaced 2 cams.When putting door back on fridge, you have to make sure door is in exact position and top hinge is lined up exactly, or door will contin
... Read more
ue to pop a little.It took me a couple of times to get top hinge lined up exactly.
Read less
Was this helpful?
Thank you for voting!
Crisper Pan Side Reales Had Cracked
10 of 11 people
found this instruction helpful.
-
LEVY from HOUSTON, TX
- Easy
- 30 - 60 mins
I just slid the new pan in , partselect has the correct part all the time , I repalced my ice maker once and it took 15 min no problem
Was this helpful?
Thank you for voting!
Broken gooseneck on fill tube
10 of 11 people
found this instruction helpful.
-
Thomas from Brunswick, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers
The gooseneck on the icemaker fill tube extends out beyond the back cabinet of the refrigerator, and is easily broken. Luckily, this part is a piece of cake to replace. You'll literally spend more time pulling out your fridge and cleaning out behind it then you will replacing this part.
Shut off water supply line, and turn of ... Read more f ice maker (lift the metal bar in the ice bucket all the way up). Loosen the hose fitting, and remove two screws. Pull out the old tube, and slide the new one in. You may have to wiggle the tube around from the inside to get the alignment correct. Replace screws and fitting. Turn water and ice maker back on, and check for leaks. It really is that easy! It took me longer to type this than to actually replace the part.
Only one potential catch. The instructions warn that you may have to cut the new tube to match the length of the old tube, so make sure you compare the length of the old and new tube. I didn't have to to do anything - the replacement part was the exact same length of the original. If by chance you do need to cut the tube, you'll need small saw of some sort, such as a coping or hack saw.
Shut off water supply line, and turn of ... Read more f ice maker (lift the metal bar in the ice bucket all the way up). Loosen the hose fitting, and remove two screws. Pull out the old tube, and slide the new one in. You may have to wiggle the tube around from the inside to get the alignment correct. Replace screws and fitting. Turn water and ice maker back on, and check for leaks. It really is that easy! It took me longer to type this than to actually replace the part.
Only one potential catch. The instructions warn that you may have to cut the new tube to match the length of the old tube, so make sure you compare the length of the old and new tube. I didn't have to to do anything - the replacement part was the exact same length of the original. If by chance you do need to cut the tube, you'll need small saw of some sort, such as a coping or hack saw.
Read less
Was this helpful?
Thank you for voting!
Didn't know if I needed Left or Right.
11 of 14 people
found this instruction helpful.
-
Joyce from Kerrville, TX
- Really Easy
- Less than 15 mins
The item is listed as R, meaning right hand side. If you need it for the left hand side, simple turn it over. It is designed to work on both sides of the door.
Was this helpful?
Thank you for voting!
auger blades broken
11 of 15 people
found this instruction helpful.
-
Michael from Ponchatoula, LA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed ice bin then pulled front cover with nut driver . Pull small rod from side ( one screw holding rod and spring). Pull auger out. Take plastic nut off end ( CLOCKWISE) LEFT HAND THREAD. Keep all ice crusher blades in order when you pull them off. Install new auger and reverse steps. web site has exploded view. It looks difficult but
... Read more
it isn't.
Read less
Was this helpful?
Thank you for voting!
Ice Door broken letting warm air into Ice Maker system which kept freezing up.
25 of 57 people
found this instruction helpful.
-
Anthony from Magnolia, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I didn't have to buy a new Ice door kit. The part on the Refrig. door I needed I found out was unavailable. The door parts (Ice door parts and the asembly for the water unit) screws into that part. I found out that I would have to replace the whole refrig. door which was $900.00. I took every apart got me some pvc glue used it on the door
... Read more
and bought the original screw online with some other assorted parts,Door switch, etc. and was able to repair in about an hour. Some of the parts are very fraigle so you have to be very careful or you will be buying some new replacement parts.The new nickel and dime parts are expensive. My Icemaker was leaking where the Ice was clumping together in the bin, and when I checked the unit was $125.00. I found a new one and replaced it for about half that price. I am now very happy! (a least until the next project.)
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
door was making a poping sound upon opening and closing
10 of 12 people
found this instruction helpful.
-
Tony from Mesquite, NV
- Really Easy
- Less than 15 mins
-
Nutdriver, Socket set
First I removed all contents from inside refrigerator door.Then I removed (1) 10mil screw,which holds cover for top hinge.Next I removed the (3) hinge screws,and lifted door off of bottom hinge.Pulled off plastic closure cam from bottom metal hinge post.I cleaned metal post ,applied a small amount of vaseline to post, slid on new plastic
... Read more
cam,installed door, replaced screws.Very easy,10 to 15 min tops.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Compressor would not kick on automatically
10 of 12 people
found this instruction helpful.
-
Robert from Brooklyn Center, MN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I removed the two screws that were readily in view. I then figured out the there was a faceplate which I was able to pry off after removing the temp control knobs. The temp control unit was easily accessible and was held by two screws which I removed with the nut driver. The only difficult part was replacing the plastic tubing which co
... Read more
vered the sending unit.
Read less
Was this helpful?
Thank you for voting!
Broken tray
11 of 15 people
found this instruction helpful.
-
Brian from Los Angeles, CA
- Really Easy
- Less than 15 mins
Remove old tray, replace with new tray.
Simple & easy.
Best part is I ordered on Monday & received on Tuesday!
Simple & easy.
Best part is I ordered on Monday & received on Tuesday!
Was this helpful?
Thank you for voting!
socket melted with bulb in it.
12 of 18 people
found this instruction helpful.
-
martin l. from JACKSONVILLE,, IL
- Really Easy
- Less than 15 mins
plastic warped in ,spaced out and, the socket snapped back in place.
Was this helpful?
Thank you for voting!
broker door on ice shute
14 of 25 people
found this instruction helpful.
-
John from Willington, DE
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
hardest part was getting up the nerve to pull front cover because it is plastic afraid i would brake it pull from bottom and lift up one screw holds old door inplace uplug electric new door doesn't have electric that it.
Was this helpful?
Thank you for voting!