3RLG Whirlpool Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
squeaking sound due to worn out bearing idler pulley wheel.
13 of 18 people
found this instruction helpful.
-
Evan from NORTHRIDGE, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
BEFORE ANYTHING ELSE UNPLUG THE POWER AND TURN OFF THE GAS SUPPLY 1. unscrew the 3 nut screws at the back to remove the cover lid. 2. pull the control console cable from the electronic board. (only 3 wires on it).3. unscrew the 2 nut scr
... Read more
ews of the control console then remove it by pulling up.4. unscrew the 5 screws to remove the door. (pull little up to unhinged then remove). 6. unscrew the 5 nut screws to remove the lower siding. 7. unscrew the copper 4 nut screws then remove the lint suction fixture 8. unscrew the 4 nut screws to remove door fixture ,then just lay next to the machine.(the wires are long enough so you don't need to unplug and separate it from the machine.9. remove the belt by pulling the idler pulley towards the motor pulley (against the tension spring) 10. remove the drum by lifting a little bit upward. 11. remove the plastic triangular lock using a small screw driver then remove the idler pulley wheel then install the replacement. (clean your machine using a vacuum cleaner and remove all the lints). 12. install back the drum, be sure to set the drum belt to the right position. (groove on drum side). 13. install back the belt to the pulley the same procedure as to remove it. 14. assemble back what you have removed. end.
Read less
Was this helpful?
Thank you for voting!
dryer would stall and the motor would hum before tripping circuit breaker
11 of 12 people
found this instruction helpful.
-
Charles from Placentia, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
When the problem first came up, I took the dryer apart without first looking up any instructions. This wasn't difficult, but didn't realize when removing the fan from the motor, there is a square lug as part of the fan hidden by the rear clamp securing the motor. I was able to remove the fan by holding the motor shaft with a crescent wr
... Read more
ench and removing the fan by hand, but was difficult and gloves were necessary in case the fan loosened quickly and my hand came in contact with the sheet metal (very sharp).
I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.
This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.
The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.
I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.
This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.
The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.
Read less
Was this helpful?
Thank you for voting!
Aft seal deterioated and causing brown spot on clothing due to netal to metal contact.
11 of 12 people
found this instruction helpful.
-
Cleo from Laurinburg, NC
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Removed top and front of dryer then drum and followed the instructions in the package. It was a real simple procedure. I did additional cleaning while the dryer was disassembled.
Was this helpful?
Thank you for voting!
Dryer stopped spinning
13 of 19 people
found this instruction helpful.
-
Danielle from FREEDOM, IN
- Really Easy
- More than 2 hours
-
Nutdriver, Screw drivers
The dryer quit working. I did some trouble shooting on your amazing site, ordered what i thought it might need and then got to work. Took no time to get it apart and replace roller kit and belt. What took the longest was getting in there and cleaning out probably 15 years worth of dirt and dust. If you have not opened your dryer up and d
... Read more
one this, 10/10 recommend, because in doing so i found that the motor was the real culprit. Once i opened it up more, especially cleaning around the blower fan and motor, i was half a day in. Put it all back together and got it running for two more loads before the motor quit. Replaced that and since the hard work was done, had it back in in half an hour and running great. Probably will need to redo the felt seal one day, but for now, i am calling it a win. This is my go to site for all things and i have been able to work on most of my major appliances and do it myself using the helpful information here.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
A piece of cloting snagged and broke the door switch.
11 of 13 people
found this instruction helpful.
-
Ronald from LANCASTER, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
Repair job took less than 10 minutes: 1) Unplug Dryer 2) Remove Lint screen and 2 Phillip screws 3) use flat putty knife to depress lid latches while lifting (latches located approx 2 - 3 inches from each side. 4) unplug defective door switch 5) remove 2 Phillip screws that secure the door switch. Reinstall switch repeating the above step
... Read more
s in reverse order and your done.
Read less
Was this helpful?
Thank you for voting!
One of the drum support rollers was worn out
13 of 19 people
found this instruction helpful.
-
David from Fleetwood, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken belt. Broken idle pully and replace 4 rollers
11 of 14 people
found this instruction helpful.
-
Mike from INOLA, OK
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.
Was this helpful?
Thank you for voting!
Dryer would not start
11 of 14 people
found this instruction helpful.
-
Daniel from Humboldt, KS
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Dryer would not start when the start switch was pushed. I was advised by the local repair shop to replace the "push to start switch" and the "thermal fuze". I unplugged the dryer and removed the back dryer casing which took all of 3 minutes. I removed the start switch and thermal fuze using directions on the whirlpool parts forum. This t
... Read more
ook maybe 5 minutes. I replaced with the new parts and put the casing back on the dryer. The entire project took 15 minutes. The dryer works perfectly. 34 USD for parts and shipping instead of 600 for a new dryer. Easy to identify the parts needed using the model number and the parts arrived the next morning I will use this company again for sure!
Read less
Was this helpful?
Thank you for voting!
broken clip on top panel hold down
15 of 26 people
found this instruction helpful.
-
Mark from Huntington Station, NY
- Easy
- Less than 15 mins
-
Screw drivers
pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.
Was this helpful?
Thank you for voting!
Idler pulley wore out
10 of 11 people
found this instruction helpful.
-
Peter from HUEYTOWN, AL
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this helpful?
Thank you for voting!
Badly worn idler pulley and rollers.
11 of 14 people
found this instruction helpful.
-
TODD from GRASS VALLEY, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Braced dryer drum with a block. Removed the two rollers one at a time by using a screwdriver to pop off the triangular clip. Slid on new rollers. Would have been easier to remove the drum out the front instead of bracing it. Installed new idler pulley and belt. Dryer is 25 years old and sounds like a new one now when running.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer does not turn off. Will stay in the Cool Down cycle
11 of 14 people
found this instruction helpful.
-
David from WINCHESTER, MA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
My dryer timer would run through the heat cycle and move in to the cool down cycle. It would not move past the cool down cycle, and would not shut off automatically. I tried replacing the Thermal Fuse first, since I'd already removed the back panel to diagnose the problem. There was no change - the dryer did not shut off automatically. Ne
... Read more
xt, I removed the back cover to the timer console. The Timer Power Resistor looks like a black circle and a rectangle joined together. It was attached to the back of the on/off switch by a single hex head screw, and the resistor has orange and black wires attached. The replacement Power Resistor doesn't look like the resistor that was in my dryer. It is rectangular in shape with 2 male spade connectors. I attached the orange and the black wires to the new power resistor. I started the dryer and it went through a full heat/cool down cycle, and automatically shut off with the end of cycle buzzer sounding. Total part replacement time was about 10 minutes.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
the directions didn't say I needed clips to hold the felt in place while I did the glue
9 of 9 people
found this instruction helpful.
-
Todd from SAN JOSE, CA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Once I started using a bunch of clothespins to hold the felt in place and then started gluing small sections at a time I was able to complete the task. The glue comes out of the tube very quickly so don't squeeze it a lot.
Other Parts Used:
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people
found this instruction helpful.
-
Dawn from Chesapeake City, MD
- Really Easy
- Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
Lint Filter screen torn and rusted
9 of 9 people
found this instruction helpful.
-
Albert from Burlington, MA
- Really Easy
- Less than 15 mins
Pulled to old out inserted the new. I would like to say your turn around from date part was ordered until I recieved it was three days, I find that amazing. I'm still waiting for a part I ordered from another company 1 month ago. The price was right shipping cost was very reasonable and your web site extremly easy to use. Thanks very m
... Read more
uch, Al
Read less
Was this helpful?
Thank you for voting!