EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3RLG Whirlpool Dryer - Instructions

All Instructions for the 3RLG
91 - 105 of 1736

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud sreeching and vibration
14 of 15 people found this instruction helpful.
  • Robert from TUTTLE, OK
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
I just followed the videos I received with the order and everything went really well. This dryer was a little different than the video, but the process was the same. The HE3 does require 4 drum rollers and I had only ordered 2. However, there was only one bad roller, so I installed both on the back of the drum. The two front rollers are pretty easy to get to if they go bad. The idler pulley was completely worn out with an 1/8 inch groove worn off to one side. PartSelect made this an easy project!
Was this helpful?
Thank you for voting!
Dryer gasket detached from screen
14 of 17 people found this instruction helpful.
  • Richard from Duarte, CA
  • Really Easy
  • Less than 15 mins
Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.
Was this helpful?
Thank you for voting!
Dryer made a terrible screeching noise when tumbling.
13 of 14 people found this instruction helpful.
  • Richard from SAUGERTIES, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
Was this helpful?
Thank you for voting!
Lint has been bypassing the lint filter and building up in the fan (and duct)
12 of 12 people found this instruction helpful.
  • David from PINETOWN, NC
  • Really Easy
  • Less than 15 mins
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Was this helpful?
Thank you for voting!
drum very loud when rotating
13 of 15 people found this instruction helpful.
  • michael from indianapolis, IN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and repl aced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.

Thanks Mike
Was this helpful?
Thank you for voting!
the dryer was making squealing noises when it first started.
13 of 15 people found this instruction helpful.
  • Christine from BIRCH RUN, MI
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
We watched the video at whirlpool.com! Made it so simple anyone could have done it!
Was this helpful?
Thank you for voting!
the drum was not turning because a broken belt
14 of 19 people found this instruction helpful.
  • thomas from bloomfield, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum expo sed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.
Was this helpful?
Thank you for voting!
Motor failure
12 of 13 people found this instruction helpful.
  • James from COTTONWOOD, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Socket set, Wrench set
Used this resource and others' advice -thank you . Make sure to disconnect power first. I had replaced the rollers and tensioner a week earlier due to squeaking, but mine was the rare one where squeaking meant motor failure, so I had to place another parts order. The dryer was 19 years old, and my blower wheel did not simply 'unscrew wi th reverse threads'. During removal the blower wheel's plastic deformed, so had to do like someone else did and cut the rear shaft with a reciprocating saw. Just be careful not to damage the bulkhead's built-in bracket that anchors the rear of the motor. I think it was a 13/16" wrench that fit the blower wheel and I forget the size for the pulley nut on the front of the motor, but I suggest a deep socket since it held well. My best advice when dealing with a motor replacement is to ensure the blower wheel wheel will separate successfully from the motor before placing your parts order should it be a stubborn removal. Good luck.
Was this helpful?
Thank you for voting!
Dry was making a loud squeaking noise.
12 of 13 people found this instruction helpful.
  • Michael from OREGON CITY, OR
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Just watch YouTube videos. They show you how step by step. Easy to install. Clean all the dust out while dryer is apart if you can with a vacuum.
Was this helpful?
Thank you for voting!
No Heat
18 of 31 people found this instruction helpful.
  • stacy m from akron, OH
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
First time ever repaired anything let alone a dryer, I watch the video and followed instructions, was pretty simple, Works like a charm
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people found this instruction helpful.
  • William from Pontiac, MO
  • Easy
  • More than 2 hours
  • Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people found this instruction helpful.
  • JEANMARIE from BELLEROSE, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
Would not start
12 of 15 people found this instruction helpful.
  • Drew from Alachua, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I tried a new switch, This did not fix the problem. Then I replaced the Fuse in the back of the unit.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Start switch didn't work, dryer ran when door closed
12 of 15 people found this instruction helpful.
  • Robert from Corvallis, OR
  • Really Easy
  • 15 - 30 mins
  • Socket set
I removed 5 screws from the back of the top panel, removed the back panel, removed the start button from front of dryer, twisted the old start switch from the back, removed the two leads, reinstalled new part in reverse order. It was that simple! 15 minutes top. Dryer works fine. Gave me a chance to vacuum out all the dust bunnies and clean out the dryer vent pipe as well.
Thanks!
Was this helpful?
Thank you for voting!
All Instructions for the 3RLG
91 - 105 of 1736