EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3RLE Whirlpool Dryer - Instructions

All Instructions for the 3RLE
121 - 135 of 934

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
My idler pully was squealing
4 of 5 people found this instruction helpful.
  • Anthony from SAINT CLOUD, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.
Was this helpful?
Thank you for voting!
Whirlpool Gas dryer, run but no heat
4 of 5 people found this instruction helpful.
  • Fred from Macomb, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I simply removed the rear panal of the dryer. Removed the two wires from the fuse at the rear of the dryer. Attached an OEM meter across the two fuse connections and had no continuity. Ordered a new fuse and recieved it in 2.5 days.Replaced the fuse,reconnected the wires and replaced the rear panal. Started dryer and it now blows hot air and runs like new. I can't say enough about PartSelect. Great diagnosis using their website, the delivery was fast and I recieved the correct part at a good price. Very satisfied, Thanks PartSelect. Fred F
Was this helpful?
Thank you for voting!
Dryer wouldn't heat.
4 of 5 people found this instruction helpful.
  • Stan from Boswell, OK
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal F use blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.
Was this helpful?
Thank you for voting!
Roller Berings were worn out - replaced both
4 of 5 people found this instruction helpful.
  • Gregory from COCOA, FL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this helpful?
Thank you for voting!
The blower wheel had fractured due to ingesting some metal objects (previous owner)
5 of 8 people found this instruction helpful.
  • virgil from BRECKENRIDGE, MI
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Followed instructions for standard blower wheel replacement and repair kit installation, which were straight forward. The only real issue I ran into was removing the blower wheel, The instructions say to turn it clockwise and remove it, however this wheel had been on there for a long time and it also has a taper shoulder so it was not coming off without a fight which is why the dremel tool is listed. I had to cut the old bower wheel out in pieces so I could remove the electric motor, which was easy. Once out and on the bench and only the metal hub left on the shaft a 7/16" wrench and large vise-grips got it to break loose. The good side of this is it allowed me to blow out any lint that had built up on the motor, like new again.
Was this helpful?
Thank you for voting!
No Gas Heat
4 of 5 people found this instruction helpful.
  • Debra from Springfield, PA
  • Very Difficult
  • More than 2 hours
  • Nutdriver
I did what any novice would have done. I took the entire thing apart to get to the gas jet. I did not know about the thermal fuse until I got to the schematic behind the timer and controls. I was a tech back in the 70's and 80's and only worked on electric dryers. Back then I would remove the heater core and twist the coils together t o save money. So I had no idea how a gas dryer heating unit worked. So now any one that reads this. You do not have to take the dryer completely apart, I did that for all of you. Just replace the thermal fuse on the back of the unit by unplugging that wires and removing the screws! It looks like a long white piece of plastic with 2 wires to it. You will find this under the full metal shield on the back of the unit. This should be about a 1 hour repair at the most!
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 3 people found this instruction helpful.
  • MONA from SHAMROCK, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.
Was this helpful?
Thank you for voting!
Dryer wouldn't shut off
4 of 6 people found this instruction helpful.
  • Jason from HUDSON, OH
  • Very Easy
  • Less than 15 mins
  • Nutdriver
The dryer would dry the clothes fine and run through heat cycles and cool down. The timer would also run down, it just would stop even thought the heat stopped. To repair, I took the back off the timer portion of the dryer. At first I panicked. I did not see any part that looked like the new one I just ordered. I searched the interne t and found that the original part looked like a black plastic loop with a black and orange wire connected to it. The part I got was the new design. Then I couldn't figure out if it mattered which end I hooked to the black wire. Another internet search showed it doesn't matter which way current flows through a resistor, so it didn't matter. Hooking in the new part was very easy. The time it took to get the information to identify the part, and determine if it matter which end to hook up to which wire took the longest. I would recommend PartSelect put a picture of the old style right beside the picture of the new style. Also would like them to make clear it doesn't matter which direction the Timer Power Resistor went in.
Was this helpful?
Thank you for voting!
Dryer would not start!
5 of 9 people found this instruction helpful.
  • Manny from ODESSA, TX
  • Really Easy
  • Less than 15 mins
  • Socket set
Unplug unit first.
Took the front cover off the front of dryer below the door.
Was this helpful?
Thank you for voting!
A hole in filter
3 of 3 people found this instruction helpful.
  • Russ from Vernal, UT
  • Really Easy
  • Less than 15 mins
Remove old filter
Vacuum out
Install new filter
Was this helpful?
Thank you for voting!
dryer would not turn on
3 of 3 people found this instruction helpful.
  • donald from MANVILLE, NJ
  • Really Easy
  • Less than 15 mins
  • Nutdriver
turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.
Was this helpful?
Thank you for voting!
Dryer would not stop, start button circuit stuck in on position
4 of 6 people found this instruction helpful.
  • Richard from Bel Air, MD
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After receiving the part I unplugged the dryer and took the back cover off of the controls on top off the driver with a Phillips screw driver and visually confirmed that the new switch matched. Removed the wires one at a time from the Push to start switch and connected them to the new one as I removed them. I then plugged the dryer back i n and tested that the new switch would fix the problem. Once I knew the new switch was the I uninstalled the bad switch and installed the new switch in to the control face. Put the cover back on and slide the dryer back in to place.
Was this helpful?
Thank you for voting!
dryer will not,dry clothes,but drum run
4 of 6 people found this instruction helpful.
  • atolfo from allentown, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Took, back cover out,but first i disconect the electricity,i give a fast look,looking for anything wrong and i saw a thermostar burn out in the element case,the bottom one,a thermostart
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve
Was this helpful?
Thank you for voting!
Dryer don't get hot !
3 of 3 people found this instruction helpful.
  • ENGEL from TRENTON, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver
It's a electric dryer, I knew it was related with the thermal !
Was this helpful?
Thank you for voting!
Belt was raffling and there was aloud knocking sound
3 of 3 people found this instruction helpful.
  • Genette from CLEVELAND, MS
  • Really Easy
  • 15 - 30 mins
  • Socket set
Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it
Was this helpful?
Thank you for voting!
All Instructions for the 3RLE
121 - 135 of 934