EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3RLE Whirlpool Dryer - Instructions

All Instructions for the 3RLE
106 - 120 of 934

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer stopping during dry cycle.
8 of 14 people found this instruction helpful.
  • James from HARTSELLE, AL
  • Very Easy
  • Less than 15 mins
  • Screw drivers, Socket set
First I pulled the dryer away from the wall and unplugged it. Next I removed the dryer vent hose and threw it away and replaced it with a more rigid metal vent hose. Next, I used a socket wrench to removed the screws holding on the back cover of the dryer. Once the back cover was off it was just a matter of using the socket wrench to remo ved the bolt holding the sensor in place. After the part was removed I made sure the replacement was orientated in the same way as the original part and then I unplugged the wires from the bad sensor and placed them in the same order on the new part and then I bolted the new sensor back in place. Since the new part has been installed the dryer is working flawlessly and is not turning off mid-cycle like it was. ***Oh, and an important reminder. When you have the back cover pulled off the dryer use a shop vacuum to suck out any dirt and lint in the back of the dryer and make sure you unbolt the metal chute that the dryer lint screen goes into and clean inside the area near the exhaust blower. This is a VERY IMPORTANT part of servicing your dryer and should be done every few months to help avoid the risk of a fire.****
Was this helpful?
Thank you for voting!
Dryer made squeaking noise, then more of a rumbling noise.
5 of 6 people found this instruction helpful.
  • JAMES from NORTH OLMSTED, OH
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Socket set, Wrench set
Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pul ley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.
Was this helpful?
Thank you for voting!
Dryer ran but without heat.
4 of 4 people found this instruction helpful.
  • barbara from SOUTHAMPTON, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Turned off my circuit breaker first. Removed back panel with a 1/4 nut driver. Replaced the dryer fuse first. Very easy but did not fix the problem. Watched how to videos to narrow down the parts I might need. Purchased the thermal cut off kit. Installed the High limit thermostat first. Tested the dryer, no dice. Finally installed the The rmal cutoff. BAM!! I have heat. Since this is an older dryer I did need to use some WD40 to loosen some of the connections. Total cost of parts including tax and quick delivery was $48.30. Fantastic. My old man told me it was unfixable. He was wrong. I WIN. This site is a great teaching site. Thank you!
Was this helpful?
Thank you for voting!
Dryer was squealing
4 of 4 people found this instruction helpful.
  • Kevin from VALDOSTA, GA
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
Was this helpful?
Thank you for voting!
Dryer drum turned hard because rollers were worn
4 of 4 people found this instruction helpful.
  • Paul from STONE CREEK, OH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this helpful?
Thank you for voting!
Idler pulley seized
4 of 4 people found this instruction helpful.
  • John from CREST HILL, IL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and rem ove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.
Was this helpful?
Thank you for voting!
Very loud squeaking noise
5 of 7 people found this instruction helpful.
  • Philip from CHICAGO, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.
Was this helpful?
Thank you for voting!
Dryer would not stop - Would heat and dry but never shut off
6 of 10 people found this instruction helpful.
  • Paul from EASTHAM, MA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Replaced the Thermal Fuse first - 30% chance - didn't help! Then I replaced the resistor - Not an in-kind replacement - looks different-Guessed the wrong place first [no specific directions :( ] and got some sparks - Yikes! Picked the second place and installed the resistor and it work PERFECT. Spent Less than $50 and back in business = G REAT!!
Was this helpful?
Thank you for voting!
My dryer was squeaking with an occasional thump
4 of 4 people found this instruction helpful.
  • Michael from BOILING SPGS, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench set
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this helpful?
Thank you for voting!
Sqeeking noise fron old worn belt and rollers
4 of 4 people found this instruction helpful.
  • Randy from HUNTSVILLE, AL
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this helpful?
Thank you for voting!
drier would not heat up
5 of 7 people found this instruction helpful.
  • PATRICK from PALOS PARK, AL
  • Easy
  • Less than 15 mins
  • Screw drivers
i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on
Was this helpful?
Thank you for voting!
Broken Drum Belt
4 of 4 people found this instruction helpful.
  • Garry from Garland, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
Just like the video, just followed the video
Thanks,
Was this helpful?
Thank you for voting!
Taking 90 minutes + to dry one load
5 of 7 people found this instruction helpful.
  • Bryan from newington, CT
  • Easy
  • 15 - 30 mins
  • Socket set
Removed the back of the dryer about 8 screws. Removed the Thermostat 250 F and replaced with new. Dries a load of clothes in one cycle on medium. Not bad for a 16 dollar part. I am a computer tech and I am used to taking computers a part but I think most people that are in anyway mechanically inclined and can look at a diagram could d o this and save yourself a lot of money.
Was this helpful?
Thank you for voting!
When door was closed the timer could be heard to continue clicking. also, drying cycle started immediately upon closing the door.
5 of 7 people found this instruction helpful.
  • Theodore from Baraboo, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Two screws hold the top control panel in place. Once removed the panel could be tipped forward. The Push to Start switch had 2 wires which were removed and swapped to the new starter switch. The old one rotated 90 degrees to remove and the new one installed. Panel was resecured to the top of the dryer and tested. Worked first time. Finding the part on the website, ordering it, receiving it quickly and the install couldn't have been easier or more pleasant or efficient.
Was this helpful?
Thank you for voting!
Dryer wouldn't heat.
4 of 5 people found this instruction helpful.
  • Stan from Boswell, OK
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal F use blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.
Was this helpful?
Thank you for voting!
All Instructions for the 3RLE
106 - 120 of 934