3973 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
support clip broken.
16 of 25 people
found this instruction helpful.
-
Arturo from Killeen, TX
- Easy
- Less than 15 mins
-
Screw drivers
After figuring out how to remove the old broken clip, replacement was easy. Had to use a small putty knife to open the release on the bottom underside of the clip(between the clip & the refrig) . By looking at the replacement piece it was easy to figure out.
Was this helpful?
Thank you for voting!
Existing light switch was hard to remove.
14 of 19 people
found this instruction helpful.
-
Stephen from Jupiter, FL
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.
Was this helpful?
Thank you for voting!
ice would not dispense
14 of 19 people
found this instruction helpful.
-
john from montgomery, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
I removed 6 screws, unplugged assembly that had motor attached,removed from fridg,replaced motor and reinstalled assembly, putting back 6 screws.works like new.
thanks.
thanks.
Was this helpful?
Thank you for voting!
Ice maker ot making ice
18 of 31 people
found this instruction helpful.
-
Barry from Phoenix, AZ
- Easy
- 15 - 30 mins
-
Nutdriver
First I replaced the double valve because the ice maker was not filling with water. It still did not work. Then I replaced the ice maker itself. This worked and was relatively easy to replace. I had to use the water fill "slide" from the old ice maker. The new one was too narrow and it leaked water into the freezer.
Was this helpful?
Thank you for voting!
Noisey Motor, Bearings Out, Dying
12 of 13 people
found this instruction helpful.
-
PERRY from VANDERBILT, MI
- Easy
- More than 2 hours
-
Nutdriver, Wrench set
Remove back cover, exposing fan motor. Turn off power, remove nut on fan blades. Remove fan carefully, do not bend. Unhook wiring harness. Remove three screws that hold the motor on the back frame. Remove old motor, install new. Carefully, reinstall fan blades, hook up wiring, and your ready for tryout. Also do some cleaning whil
... Read more
e your there. Clean old fan blades with hot soapy water or contact cleaner. Everything runs better clean!
Read less
Was this helpful?
Thank you for voting!
Refrigerator Door Wouldn't Close Right
13 of 17 people
found this instruction helpful.
-
Anthony from Highland Lakes, NJ
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench set
Get 2 "door closing cams" yep. Same as some others here. Found some black plastic pieces on the floor, when door wasn't closing right. I took the door off by taking off the top bracket. Very easy. Bottom bracket has the broken cam riveted to it. Need hacksaw to get this off then punch it through with hammer and a screwdriver. This
... Read more
is the only part that took a little while. Replace the closing cam and find a small nut & bolt or screw to replace the rivet you just sawed in half. Replace the closing cam that is on the bottom the the door as well. Even if yours isn't broken. Replace it anyway. Put door back on and done. Not a diffucult project if you know about the rivet and needing 2 closing cams beforehand. Good luck
Read less
Was this helpful?
Thank you for voting!
The cam broke apart and the pieces were on the floor. The door did not close automatically. This was on the freezer side.
12 of 14 people
found this instruction helpful.
-
Bennie from Gainesville, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I used the same steps as described in other descriptions listed here. Since I was changing the hinge assembly on the freezer side the difference I discovered was that there was a nylon water hose inside the hinge assembly that I did not at first know how to remove. I finally called a repairman I happened to know and following his instru
... Read more
ction simply snapped the hose loose where there was a connector and placed a cloth under it to catch the moisture that drained. Having done that, the rest of the assembly went just the same way as the other instructions listed here said that it would. Door now functions like new.
Read less
Was this helpful?
Thank you for voting!
Light in the refrigerator went out
13 of 18 people
found this instruction helpful.
-
Paulette B. from Santa Ana, CA
- Really Easy
- 15 - 30 mins
After I bought what I thought I needed for the repair. I asked a friend to come over and look at it. He changed the
the light socket and put the same light bulb in and it works great. I am returning the light switch but decided to keep the light bulb.
Getting on the internet was so easy. This was really very simple. ... Read more Thank you for making what I thought would be a big ordeal into something very simple.
Paulette Johnson
the light socket and put the same light bulb in and it works great. I am returning the light switch but decided to keep the light bulb.
Getting on the internet was so easy. This was really very simple. ... Read more Thank you for making what I thought would be a big ordeal into something very simple.
Paulette Johnson
Read less
Was this helpful?
Thank you for voting!
Fridge wouldn't start
12 of 15 people
found this instruction helpful.
-
Patrick from Medford, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed cowling unpluged timer and pluged in new one.
Great Service, got part in one day
Great Service, got part in one day
Was this helpful?
Thank you for voting!
Flapper was stuck open. Old and warped.
16 of 27 people
found this instruction helpful.
-
James from Virginia Beach, VA
- Easy
- 15 - 30 mins
-
Screw drivers
Replaced flapper
Was this helpful?
Thank you for voting!
Interior light needed replaced
22 of 46 people
found this instruction helpful.
-
Leo from TWIN FALLS, ID
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Was this helpful?
Thank you for voting!
The refrigerator section of my side by side was not getting as cold as it should have been.
10 of 10 people
found this instruction helpful.
-
Wayne from Magnolia, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
It was easy after finding PartSelect online. It wasn't obvious at first that my evaporator core(in back of freezer side) was frosting over, (since I have a flat white panel that is about 8 x 30 inches covering it), until I reached inside and ran my fingers over the cover and noticed a thin layer of frost on it. At this point I told my bud
... Read more
dies to go get ice for our beer cuz I was fixin to do a lock out/tag out on the Fridge. Seriously, Do disconnect the electrical power before taking it apart. After taking the 9 screws (6-1/4" hex heads & 3-#2 phillips)out and removing the panel, I saw that the evaporator core was completely frosted over. I then put a large towel in the bottom and let it thaw for a day. Next day after getting the old Defrost Heater Kit with Thermostat out (4-#2 phillips, plug-in electrical connection, thermostat snap on clip) , I noticed it was burnt inside the filaments and did not pass the continuity test. I then ordered my part from PartSelect and took the oppurtunity to clean my fridge spotless. 3 business days later, I received my part, installed it, and now have a "like new" refrigertor. Actual repair time - 30 minutes, Overall down time - 4 days, Saving the cost of a new Fridge - a heck of lot more beer!
Read less
Was this helpful?
Thank you for voting!
Defrost Thermostat quit working
11 of 13 people
found this instruction helpful.
-
Jimmy from Palmer, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
Take the back panel off inside of freezer side. Cut the wires off old Defrost Thermostat and strip the ends. Attach the wires of the new one and tighten with wire nuts. Put back panel back on.
Was this helpful?
Thank you for voting!
Refridgerator Freezer stoped making ice
17 of 31 people
found this instruction helpful.
-
Marion from Palm Coast, FL
- Easy
- 30 - 60 mins
-
Screw drivers
Turned off power, removed cover from Ice maker, checked resistance across thermostat for zero (read open), all other switches read proper value (when activated). Ordered and received thermostat. Removed Ice Maker from freezer, removed two screws holding ice tray to Control Assembly. Removed Thermostat and replaced with new one. Applied Si
... Read more
licone Sealant to face of Thermostat for adhesion to ice tray when assembled. Remounted Ice Tray to Control Assembly and remounted in freezer. Works Great...
Read less
Was this helpful?
Thank you for voting!
fridge quit coolingg / freezing
11 of 13 people
found this instruction helpful.
-
JEFF from HAMPTON, GA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
remove lower back cover - disconnect wires to fan motor - place 6" fan to blow on condenser - fridge began cooling & freezing again - ordered part - part arrived - removed fan motor & bracket - cleaned brackets & fan blade - cleaned lint & dust from condenser compartment (took longer to clean than anything else) - replaced fan motor - rep
... Read more
laced cover - was hero with wife ... :-)
Read less
Was this helpful?
Thank you for voting!