EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3962 Magic Chef Microwave Oven Combo - Instructions

All Instructions for the 3962
121 - 135 of 197

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
heating coils would not work
  • Adam from Kempner, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.
Was this helpful?
Thank you for voting!
Burner did not heat
  • lula from Antelope, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
New receptacle element. I am a girl and I did it.!!!!
Was this helpful?
Thank you for voting!
temperature varied in oven.couldn't set
  • tom from winter haven, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair
Was this helpful?
Thank you for voting!
Used stove was missing 1 leg.
  • Clarence from Monroe, WI
  • Really Easy
  • Less than 15 mins
  • Pliers
My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.
Was this helpful?
Thank you for voting!
Burner receptacle had malfunctioned and been removed
  • Kerry from Silverado, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
10 Minutes for a stove my landlord thought was not fixable (repairman had already cut the wires to the element and capped them)! The delivery person handed me the package, I got out the single tool needed, installed the part, put away the tool, cleaned my hands, and put a pot of water on the stove to boil for pasta. 10 minutes!
Was this helpful?
Thank you for voting!
Broken leveling leg.
  • Don from Crestwood, MO
  • Really Easy
  • Less than 15 mins
  • Pliers
This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.
Was this helpful?
Thank you for voting!
Oven would not turn on
  • Stacey from Tampa, FL
  • Easy
  • Less than 15 mins
  • Screw drivers
Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.
Was this helpful?
Thank you for voting!
Oven have F2 and F3 codes following cleaning cycle making oven inoperable
  • Timothy from Longmeadow, MA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!
Was this helpful?
Thank you for voting!
one pole of the socket corroded to nothing
  • martien from williamstown, MA
  • Easy
  • Less than 15 mins
Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.
Was this helpful?
Thank you for voting!
Oven would overheat
  • MARK from roseville, MN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.
Was this helpful?
Thank you for voting!
Light bulb failure
  • Grant from Alexandria, VA
  • Really Easy
  • Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
Temp spikes.
  • Wayne from Grantsburg, WI
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.
Was this helpful?
Thank you for voting!
oven temperature only goes to 275 degrees even when set higher; broiler works
  • Anne Marie from Huntingdon Valley, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.
Was this helpful?
Thank you for voting!
Cartridge wire burned out
  • Robert from San Francisco, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.
Was this helpful?
Thank you for voting!
Top oven sensor
  • Alan from Bonita, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers
The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires to gather. The oven cooks fine, I have not tried the cleaning cycle yet.
Was this helpful?
Thank you for voting!
All Instructions for the 3962
121 - 135 of 197