3962 Magic Chef Microwave Oven Combo - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bulb Replacement
0 of 2 people
found this instruction helpful.
-
Judith from Phoenix, AZ
- Really Easy
- Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
2 of the small burners just fell apart
1 of 5 people
found this instruction helpful.
-
Janice M from Ocala, FL
- Really Easy
- Less than 15 mins
I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You
Was this helpful?
Thank you for voting!
Oven would not work
0 of 2 people
found this instruction helpful.
-
george from San Antonio, TX
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench set
Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!
Was this helpful?
Thank you for voting!
Surface Element got hot spot and burned out. Then bad burner would not go off
-
Glenn from Long Valley, NJ
- Easy
- 1- 2 hours
-
Screw drivers
Our Maytag Gemini is about 10 years old. One night the 8" front right element was smoking and had a white hot spot on the burner. I quickly turned it off and after the element cooled I removed it. Since one 8" element was burned out, but the rest of the range and oven worked, I assumed I could get it fixed. Rather than call the service m
... Read more
an for $99 for a diagnostic visit, I decided to go to PartSelect and get prices on parts. They had the easiest site to use with part numbers, exploded part drawings, etc. Since I had to replace one burned out element anyway, I ordered the burner and the wiring receptacle. I assumed that was step one. The parts came in about two days. It took me about 20 minutes to put them in with no problems. Very easy. However, the burmer still would not work. I went back to the site and determined the only other part it could be was the infinite switch. The bad element little light on the top control panel was not going out even after I put in new parts. I figured it was shorted out and frozen in the closed position, so I ordered a new one from PrtSelect. It came again in about two days. This part was easy to replace, except it took longer because the entire back of the oven had to be removed. Three pieces of sheet metal had to be removed and two plastic end caps. Sheet metal has sharp edges. Watch out that you do not get cut. A lot of screws got removed and put back. You have to be careful that the three pieces of sheet metal are put back correctly because several edge tabs lap over each other. The infinite switch fixed the problem. Took me about two hours to do the switch replacement, but that counted cleaning the sides of the oven and underneath the oven (Yuch!). Now everything works fine. I suspect that the old wiring receptacle was fine and just the infinite switch and element needed to be replaced. In any case, the wiring receptacle was cheap. In the end, the repair cost me the same $99, but I spent it in parts and not parts plus installation so I was way ahead.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Burner element stopped working
-
Robert from Lodi, CA
- Really Easy
- 1- 2 hours
-
Screw drivers
The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not
... Read more
a pretty picture, but that's how repair work is on old stuff.
Read less
Was this helpful?
Thank you for voting!
Front 8" stove burner got excessively hot at any setting
-
John from Manchester, MI
- Really Easy
- 30 - 60 mins
-
Screw drivers
Performed repairs just as you directed. Everything went in in without a hitch. All the parts fit well and seem to be working fine. Wife still complains. Maybe I need a new burner coil.
Other Parts Used:
Was this helpful?
Thank you for voting!
Front burner would not heat properly.
-
Michael from Milton, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.
Was this helpful?
Thank you for voting!
Porcelan Electric Burner Plug broke
-
John J from Coatesville, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website
... Read more
.
Read less
Was this helpful?
Thank you for voting!
one of my 8" burners got really red in one spot and then had flame.
-
Pamela from Ballantine, MT
- Really Easy
- Less than 15 mins
So purchased two new 8 inch elements and replaced them.
Was this helpful?
Thank you for voting!
Oven light Switch
-
William from APACHE JUNCTION, AZ
- Really Easy
- Less than 15 mins
-
Pliers
Compressed the springs and removed the damaged switch, then changed the wiring over to the new switch and press into place, worked fine.
Was this helpful?
Thank you for voting!
Fan runs continually ,door locked,error code f2,f3,f7
-
John from Dacula, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with m
... Read more
atched harness /.connection, installed 2 screws ,turned on breaker.
Read less
Was this helpful?
Thank you for voting!
Broken plastic knob
-
Judy from McKinney, TX
- Really Easy
- Less than 15 mins
Placed new knob directly on post. No problem
Was this helpful?
Thank you for voting!
Had code F1 and F3 on my oven. Oven wouldn't heat.
-
Cindy from Polson, MT
- Really Easy
- Less than 15 mins
-
Screw drivers
Watched the video and it was as easy as described. Not many things go as easily as this.
Was this helpful?
Thank you for voting!
change oven sensor
-
Lloyd from Eau Claire, WI
- Really Easy
- Less than 15 mins
-
Screw drivers
Followed provided video
Was this helpful?
Thank you for voting!
surface burner stopped working. Was not heating up.
-
timothy from south bend, IN
- Really Easy
- Less than 15 mins
-
Nutdriver
The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call
... Read more
would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)
Read less
Was this helpful?
Thank you for voting!