EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38HB Magic Chef Range - Instructions

All Instructions for the 38HB
121 - 135 of 218

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not work
0 of 2 people found this instruction helpful.
  • george from San Antonio, TX
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench set
Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!
Was this helpful?
Thank you for voting!
gasket was leaking heat from oven
2 of 12 people found this instruction helpful.
  • NORMAN W from Waleska, GA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
removed old and installed new
Was this helpful?
Thank you for voting!
oven not staying on. fault cod F-3 showing
  • James from Cumberland, MD
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.
Was this helpful?
Thank you for voting!
Temp spikes.
  • Wayne from Grantsburg, WI
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.
Was this helpful?
Thank you for voting!
Oven would not heat
  • Claude from Lakewood, OH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)
Was this helpful?
Thank you for voting!
Oven would overheat
  • MARK from roseville, MN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.
Was this helpful?
Thank you for voting!
replacement of heating element for elec. stove
  • Erica from Ivyland borough, PA
  • Really Easy
  • Less than 15 mins
plugged it in to the spot where missing element was.
Was this helpful?
Thank you for voting!
The drip pans needed replacing.
  • Alison from Carnation, WA
  • Really Easy
  • Less than 15 mins
Put in the new drip pan -- which are really nice shiny ones.
Was this helpful?
Thank you for voting!
Dirty drip bowls
  • Paul from Carnegie, PA
  • Really Easy
  • Less than 15 mins
Just remove old bowls from range top and put new ones. That is all ... just super simple! :)
Was this helpful?
Thank you for voting!
Dirty drip bowl
  • Paul from Carnegie, PA
  • Really Easy
  • Less than 15 mins
Remove old drip bowl from the range and put a new one back.
Was this helpful?
Thank you for voting!
Had code F1 and F3 on my oven. Oven wouldn't heat.
  • Cindy from Polson, MT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Watched the video and it was as easy as described. Not many things go as easily as this.
Was this helpful?
Thank you for voting!
Oven would not heat up properly to set temperature
  • Max from Bothell, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced wi th a new one.
Was this helpful?
Thank you for voting!
change oven sensor
  • Lloyd from Eau Claire, WI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Followed provided video
Was this helpful?
Thank you for voting!
drip pan were burnt out
  • Delroy from Miramar, FL
  • Really Easy
  • Less than 15 mins
simply remove the burner take out the drip pan and bowl individually. Install the new one and replace the burner. no tool was used.
Was this helpful?
Thank you for voting!
burner not working
  • Marcia from Wellesley, MA
  • Really Easy
  • Less than 15 mins
burner replaced
Was this helpful?
Thank you for voting!
All Instructions for the 38HB
121 - 135 of 218