38HB Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The three braces under the coils had weakened and fallen apart
2 of 5 people
found this instruction helpful.
-
Suzanne from COZAD, NE
- Very Easy
- Less than 15 mins
I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.
Was this helpful?
Thank you for voting!
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
1 of 2 people
found this instruction helpful.
-
Nicki from ELSIE, NE
- Very Easy
- Less than 15 mins
No problem Took off old ones and replaced with new.
Was this helpful?
Thank you for voting!
Drip pans needed to be replaced
1 of 2 people
found this instruction helpful.
-
Mark from ROSENBERG, TX
- Very Easy
- Less than 15 mins
1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements
Other Parts Used:
Was this helpful?
Thank you for voting!
Burners needed replacing
1 of 2 people
found this instruction helpful.
-
Alene from INDIANAPOLIS, IN
- Very Easy
- Less than 15 mins
Pulled out the old burners and put in the new ones.
Was this helpful?
Thank you for voting!
Broiler element broken
1 of 2 people
found this instruction helpful.
-
Walter J from Boynton Beach, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Very simple, unscrew the old element. Remove the electrical spade connectors and reverse to install new element. The folks at parts select.com were very helpful and even after I ordered the wrong part, the return process was hassle free. Prompt shipping, very happy.
Was this helpful?
Thank you for voting!
Top oven element works, but bottom element works only intermittently
2 of 5 people
found this instruction helpful.
-
Bruce from Glencoe, MN
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.
Was this helpful?
Thank you for voting!
Oven Over Heating
1 of 2 people
found this instruction helpful.
-
Steve from New Albany, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.
Was this helpful?
Thank you for voting!
burned out stove eye, 6"
1 of 2 people
found this instruction helpful.
-
Robert from Birmingham, AL
- Easy
- 15 - 30 mins
remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan
Was this helpful?
Thank you for voting!
F1-1 and F3-1 error code
2 of 5 people
found this instruction helpful.
-
Barbara from Lakeville, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem.
... Read more
Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...
Read less
Was this helpful?
Thank you for voting!
element shorted out startedto arch inside oven
1 of 3 people
found this instruction helpful.
-
David from Traverse city, MI
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Turned off power, first then removed two screws
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.
Was this helpful?
Thank you for voting!
surface burner heating element broken
2 of 6 people
found this instruction helpful.
-
Marlene from Charleston, SC
- Really Easy
- Less than 15 mins
took out old element, replaced with new.
Was this helpful?
Thank you for voting!
missing clock knob
1 of 3 people
found this instruction helpful.
-
Jimmie from Hampton, VA
- Really Easy
- Less than 15 mins
placed knob on clock shaft with my fingers
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people
found this instruction helpful.
-
Ivanka from Atlantra, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh
... Read more
t bulb in was not the problem.
Read less
Was this helpful?
Thank you for voting!
Oven temperature lagging set temperature by almost 100F
0 of 1 people
found this instruction helpful.
-
William from Edgewood, WA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order
Unfortunately, neither the new bake element or sensor fi ... Read more xed the problem, so I just ordered the more expensive control board -- hope that does it.
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order
Unfortunately, neither the new bake element or sensor fi ... Read more xed the problem, so I just ordered the more expensive control board -- hope that does it.
Read less
Was this helpful?
Thank you for voting!
Little or no heat from oven, cakes baking unevenly
3 of 10 people
found this instruction helpful.
-
STEVE from Lehigh Acres, FL
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced both parts to not take any chances. Had to first find the hole in the back of the oven for the temperature sensor kit. We were trying too hard and overlooked the obvious. It goes behind the small black panel, as you look at the back of the stove it is top left and held in place by only one screw. Once we found it everything went
... Read more
very well and the oven is working great-back in the cake business again!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!