EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38FK Magic Chef Range - Instructions

All Instructions for the 38FK
16 - 30 of 237

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Small Element On Counter Top Range Not Heating.
17 of 20 people found this instruction helpful.
  • Brian E from Waldorf, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
1. Turned off power to trouble shoot the counter top range elements. 2. Raised the counter top up to work on it and slid two evenly placed wooden slats under the bottom of the housfor stability so it would not fall backdown into the counter top cut-out. 3. With a 1/4" nut driver removed the 10 hex-head screw that were holding the blac k glass top in place, pulled off the 4 . Control knobs and carefully removed the glass cover and carefully seet it aside in a safe place. 5. A visual inspection of the non working element showed that it had a burn out spot causing it not to heat. 6. Got the model number of the appliance and checked the internet for parts suppliers, chose parts elect because they had the part in stock and could overnight it for reinstallation the next day, part did arrive the next morning. A visual inspection show that it was the correct part and it would be a like for like swap out. 7. Prior to replacing the element check to see that the electrical power was still off at the circuit breaker, made a quick sketch of the wiring and identified the wires so that they would be reterminated at the same points. 8. Using the needle nose pliers pulled off the 4 stake on terminations. 9. Lifted out the 6" from the body of the unit , removed the 4 phillips screws holding parts what were to be transfered onto the new element. 10. Transfered parts onto the new element, reinstalled the element into the body of the unit, reinstalled the 4-stake-on wires to there appropriate terminals and verified with previous wiring sketch. 11. Reinstalled the glass top, 10 screw holding it in place and the 4-control knobs. 12 . Turned main power to the unit back on and turned on the replaced element, it work correctly, also checked the other 3 elements to make sure that they were working correctly. 13. When the unit had cooled, removed the wooden slats and lowered the counter top back into its cut-out making sure not to damage the glasstop. Job complete.
Was this helpful?
Thank you for voting!
oven door spring broke and had to be replaced, oven light out and had to be replaced
16 of 19 people found this instruction helpful.
  • Ed from Anderson, IN
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
The old gasket fell apart as I replaced the oven light and had to be replaced. That was very easy once I received the part. The spring broke on the oven door and had to be replaced. I initially tried to reach in from inside the pan drawer under the oven. That was impossible to reaach but it only took a few minutes to realize that I ha d to remove the side panel. I had to slide the range out from between the cabinets, but once that was done it was a relatively easy fix, without any special tools needed.
Was this helpful?
Thank you for voting!
defective oven sensor
17 of 23 people found this instruction helpful.
  • sean from easthampton, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires to gether and reattached sensor inside oven. A cakewalk.
Was this helpful?
Thank you for voting!
Overshooting temperatures upon changing settings
15 of 17 people found this instruction helpful.
  • James from Palmdale, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.
Was this helpful?
Thank you for voting!
Element burned out
18 of 28 people found this instruction helpful.
  • Anita from Hudson, CO
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.
Was this helpful?
Thank you for voting!
Light Bulb burned out
12 of 12 people found this instruction helpful.
  • Jeffrey from Marietta, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. Th e order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.
Was this helpful?
Thank you for voting!
oven would't go on
12 of 14 people found this instruction helpful.
  • James from Fords, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!
Was this helpful?
Thank you for voting!
Code said we needed a sensor
12 of 14 people found this instruction helpful.
  • Janice from Portland, OR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.
Was this helpful?
Thank you for voting!
oven would not maintain temp
12 of 14 people found this instruction helpful.
  • doyle from demorest, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor
Was this helpful?
Thank you for voting!
spring broke on one side of door hinge
14 of 20 people found this instruction helpful.
  • Travis from Lexington, OK
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.
Was this helpful?
Thank you for voting!
After self cleaning the oven received an error code telling me the sensor was bad.
11 of 13 people found this instruction helpful.
  • Christine from Davie, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working corre ctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )
Was this helpful?
Thank you for voting!
oven getting 50 degrees or more, hotter than setting
10 of 10 people found this instruction helpful.
  • Joseph from Wappingers Falls, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.
Was this helpful?
Thank you for voting!
F1 code and oven wouldn't operate
11 of 15 people found this instruction helpful.
  • Robbie from Hillsboro, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on . Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.
Was this helpful?
Thank you for voting!
Burner not working
12 of 18 people found this instruction helpful.
  • Warren C from Slidell, LA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First thing- I cut off power to the range. I then removed two screws to allow the cook top to be lifted. I marked the wiring and replaced the burner. Reapplied power and started cooking!
Was this helpful?
Thank you for voting!
F-3 error code
8 of 8 people found this instruction helpful.
  • Mark from Lake Orion, MI
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.
Was this helpful?
Thank you for voting!
All Instructions for the 38FK
16 - 30 of 237