EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3882 - Instructions

All Instructions for the 3882
76 - 90 of 523

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Needed to replace the oven door gasket/seal
4 of 5 people found this instruction helpful.
  • Daniel from Katy, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.
Was this helpful?
Thank you for voting!
Broiler part wouldn't heat. Element internally broken
5 of 8 people found this instruction helpful.
  • Richard from Perkinsville, VT
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
i removed the two screws that holds the element in. I pulled the element out and disconnected the wires and I had to adapt a double male adapter to the wire ends and plug the wires back onto the element. The old element had male spades and the new element had female spades.
Was this helpful?
Thank you for voting!
Oven erratic, not heating correctly, timer beeper sounding
3 of 3 people found this instruction helpful.
  • Dave from SANTA BARBARA, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Was this helpful?
Thank you for voting!
door seal contaminated by a boil-over, not flexible
3 of 3 people found this instruction helpful.
  • Rob from Yakima, WA
  • Really Easy
  • Less than 15 mins
From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.
Was this helpful?
Thank you for voting!
Old coil broke.
6 of 12 people found this instruction helpful.
  • Paula Collins from Needham, MA
  • Really Easy
  • Less than 15 mins
After I removed the piece of metal separating the two wires, I inserted the unit with no problem.
Was this helpful?
Thank you for voting!
Broiler drawer front slide plastic guides broke so drawer sagged and was difficult to pull out.
3 of 3 people found this instruction helpful.
  • DOUGLAS from MESA, AZ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the single phillips screw that held each plastic slide guide to the stove, and replaced the part reusing the screws. Was so simple I didn't even have to swear. This was my mother-in-law's stove, and she was so happy to have it repaired she's fed me twice since.
Was this helpful?
Thank you for voting!
Gasket was worn out.
3 of 3 people found this instruction helpful.
  • Michael from VALLEJO, CA
  • Really Easy
  • Less than 15 mins
  • Pliers
Put a new one in.
Was this helpful?
Thank you for voting!
broken terminal
3 of 3 people found this instruction helpful.
  • Gary from Shirley, IN
  • Really Easy
  • Less than 15 mins
Simply removed the old heating element and plug the new element terminals into socket.
Was this helpful?
Thank you for voting!
Old element caught fire, replaced with new one
3 of 3 people found this instruction helpful.
  • louis from CAHOKIA, IL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Removed screws of old element pulled clips off replaced with new element very easy
Was this helpful?
Thank you for voting!
Oven heat loss, door gasket needed replacement
3 of 4 people found this instruction helpful.
  • Stephen from Chapell Hill, NC
  • Really Easy
  • Less than 15 mins
The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in plac e! Simple!
Was this helpful?
Thank you for voting!
Broiler front drawer slides broke
3 of 4 people found this instruction helpful.
  • Ernie from Fremont, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concis e diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.
Was this helpful?
Thank you for voting!
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
3 of 4 people found this instruction helpful.
  • George from Irving, TX
  • Really Easy
  • Less than 15 mins
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Was this helpful?
Thank you for voting!
Broiler drawer didn't track poperly
3 of 4 people found this instruction helpful.
  • Keith from Atlanta, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).
Was this helpful?
Thank you for voting!
ovens wouldn't maintain temperature after preheat cycle
3 of 4 people found this instruction helpful.
  • sherri from elk horn, IA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.p lugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
Was this helpful?
Thank you for voting!
The inside glass was broken on oven door.
3 of 4 people found this instruction helpful.
  • Jacob from Cotton, MN
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I was pleased with how the job went.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
Was this helpful?
Thank you for voting!
All Instructions for the 3882
76 - 90 of 523