3882 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
5 of 5 people
found this instruction helpful.
-
Aubrey from EADS, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
Was this helpful?
Thank you for voting!
electric burner burned out
6 of 9 people
found this instruction helpful.
-
Paul from Foley, AL
- Really Easy
- Less than 15 mins
This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartri
... Read more
dge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.
Read less
Was this helpful?
Thank you for voting!
Bake Element Failed
5 of 6 people
found this instruction helpful.
-
Douglas from Plymouth, WI
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplugged the stove. I removed the old element by removing the two screws holding it in, and plugged the stove back in. I ordered the part and it came in 2 days. Unpluged the stove again, connected the new element, and re-attached it via the two screws. Plugged it back in, and it worked great. Fantastic price and quick delivery. Only too
... Read more
k about 5 minutes to fix, and I saved at least $100 by not having to call a service man.
Read less
Was this helpful?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
5 of 6 people
found this instruction helpful.
-
Sharon from Yacolt, WA
- Really Easy
- Less than 15 mins
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
Other Parts Used:
Was this helpful?
Thank you for voting!
6" surface heating coil remained warm when "off"
8 of 15 people
found this instruction helpful.
-
William C. from Sealy, TX
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sl
... Read more
eeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.
Read less
Was this helpful?
Thank you for voting!
The heating element socket had crumbled with age.
4 of 4 people
found this instruction helpful.
-
Edward from Webster, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.
Was this helpful?
Thank you for voting!
burner fell apart
5 of 7 people
found this instruction helpful.
-
Barbara a from Huntington, NY
- Really Easy
- Less than 15 mins
Plugged in the new burner, which we received in one day.We were delighted with the quick service
Was this helpful?
Thank you for voting!
power light on, but burner not getting hot
7 of 13 people
found this instruction helpful.
-
Aaron from Weymouth, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.
Was this helpful?
Thank you for voting!
Door gasket was hard and brittle from baked-on grease - heat leaking around door
4 of 5 people
found this instruction helpful.
-
Harlen from Spring Creek, NV
- Really Easy
- Less than 15 mins
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in
... Read more
each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.
Read less
Was this helpful?
Thank you for voting!
Oven was not correctly heating to set temperature
4 of 5 people
found this instruction helpful.
-
Trace from Ofallon, MO
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces
... Read more
of sheet metal back on and plugged in the oven.
Read less
Was this helpful?
Thank you for voting!
The drip bowls were all caked and corroded.
4 of 5 people
found this instruction helpful.
-
Terry from Mountain City, TN
- Really Easy
- Less than 15 mins
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken levelling leg
5 of 8 people
found this instruction helpful.
-
Linda from Oneida, NY
- Really Easy
- Less than 15 mins
Took the old levelling leg out and screw the new one in.
Was this helpful?
Thank you for voting!
Burner no longer worked.
4 of 5 people
found this instruction helpful.
-
Marcus from Emmett, KS
- Easy
- Less than 15 mins
-
Screw drivers
First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!
Was this helpful?
Thank you for voting!
Panel light burnt out after 10 years
4 of 5 people
found this instruction helpful.
-
Pamela from La Junta, CO
- Really Easy
- Less than 15 mins
I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just
... Read more
4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .
Read less
Was this helpful?
Thank you for voting!
oven overheated F-2 error message
6 of 11 people
found this instruction helpful.
-
Russell from Juneau, AK
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
replaced Hi-Limit button by removing rear oven cover. Changing by removing screws than replacing with new button.................................. changed sensor by removing screws inside oven and replcing with new unit. changed connector behind rear cover.
Other Parts Used:
Was this helpful?
Thank you for voting!