3867V Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
bake element disintegrated!
1 person
found this instruction helpful.
-
Susan from Grand Ledge, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Seems every 5 years this bake element totally disintegrates, so we,re experienced! Pull the stove out and remove the back, remove the 2 screws that hold the element(now in 5 pieces), diconnect and discard. Place new element in and connect, replace the 2 screws holding the element in place. Replace stove back. Easy
Was this helpful?
Thank you for voting!
Oven door was locked, couldn't set oven temps
1 person
found this instruction helpful.
-
William from Nashville, TN
- Easy
- 15 - 30 mins
-
Screw drivers
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off)
... Read more
now turned off. That's a lot of things working better for less than $50!
Read less
Was this helpful?
Thank you for voting!
Replaced Burned-out Cooktop Element
1 person
found this instruction helpful.
-
Seth from Old Orchard Beach, ME
- Easy
- 15 - 30 mins
-
Nutdriver
Exact fit, but read the instructions! Male connectors on element are labeled 1A 1B 2A 2C, very faintly etched in the ceramic. Even though the old and new elements look the same (and I took photos to aid installation), the connector locations are different -- 1A on the old element is where 2B on the new one is, etc. Used included exten
... Read more
sion wire for one that would not reach with the new configuration and everything works perfectly.
Read less
Was this helpful?
Thank you for voting!
Bottom Element Burned out
1 person
found this instruction helpful.
-
Robert from Jacksonville, FL
- Easy
- 15 - 30 mins
-
Screw drivers
Turned off all power to range.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)
Reversed the process.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)
Reversed the process.
Was this helpful?
Thank you for voting!
oven didn't heat up
1 person
found this instruction helpful.
-
robert from merrimack, NH
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.
Was this helpful?
Thank you for voting!
Lower burner not heating:
1 person
found this instruction helpful.
-
John from Fishers, IN
- Easy
- 15 - 30 mins
-
Screw drivers
Ordered element and recieved in two days(yea). Removed back cover from unit. Removed two wire slide on wire clips. Then went inside oven cavity and removed two screws holding element intact. The element slid out. Installed element, re-installed two screws to hold element intact. Attached wire clips back on to element, re-attached back
... Read more
cover. Plugged unit back in and it worked perfectly. Eazy-peezy lemon squeezy.
John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600
John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600
Read less
Was this helpful?
Thank you for voting!
My original back leg broke because the floor is uneven. Had to pull it out several times.
1 person
found this instruction helpful.
-
Phyllis from BROWNVILLE, NY
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this helpful?
Thank you for voting!
One of the broiler drawer guides broke
1 person
found this instruction helpful.
-
Jeri from NEW RICHMOND, OH
- Very Easy
- Less than 15 mins
-
Screw drivers
All I had to do was pull the drawer out and screw on the new part! Awesome experience...and it was so easy to find the part on the website, everything is very clear and with pictures to ensure where the part belongs...who could ask for more?
Was this helpful?
Thank you for voting!
Oven would not hold temperature, not turn on, and would shut off during use.
1 person
found this instruction helpful.
-
John from Arvada, CO
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Phili
... Read more
ps head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.
Read less
Was this helpful?
Thank you for voting!
Element didn't heat at all
1 person
found this instruction helpful.
-
Roger from PATERSON, NJ
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Removed 2 screws, disconnected wires, attached wires to new element, put screws back. Turned oven on. Perfect.
Was this helpful?
Thank you for voting!
No problem installing the sensor
1 person
found this instruction helpful.
-
tommy from FAYETTEVILLE, NC
- Very Easy
- Less than 15 mins
-
Screw drivers
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this helpful?
Thank you for voting!
The Baking Element won't heat to bake.
1 person
found this instruction helpful.
-
Kiara from JACKSONVILLE, FL
- Very Easy
- Less than 15 mins
-
Screw drivers
I had the problem before and had to call in a Tech to repair the baking element in my oven. It cost me $150.00 for the repair. This time I decided to do the repair myself, so I went online and found this site The instruction video made it very easy. I am very proud of what I was able to do without calling a Tech. My oven works like new, I
... Read more
t only cost less than $40.00 for the total repair. I am so glad this site were there when I needed them.. Thanks a Lot..
Read less
Was this helpful?
Thank you for voting!
Bake element burned out
1 person
found this instruction helpful.
-
Richard from BOULDER, CO
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Removed the failed bake element per the video linked in the Partselect email. Unlike the video on YouTube the PartSelect video shows that the bake element can easily be replaced through the oven door and it is not necessary to slide the range out and remove a rear panel.
Was this helpful?
Thank you for voting!
The bake oven element burned out
1 person
found this instruction helpful.
-
Robert from LEXINGTON, MA
- Very Easy
- 15 - 30 mins
-
Screw drivers
Removed two screws and disconnected the element. Reconnected the new element and reinstalled the screws
Was this helpful?
Thank you for voting!
Element burn out. Would not heat
1 person
found this instruction helpful.
-
Dennis from AIKEN, SC
- Very Easy
- 15 - 30 mins
-
Nutdriver
Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall
... Read more
screws and turn Circuit breaker power back on. Done and Done
Read less
Was this helpful?
Thank you for voting!