EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3862 - Instructions

All Instructions for the 3862
46 - 60 of 587

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The oven stopped heating
10 of 11 people found this instruction helpful.
  • GENE from TRENTON, SC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I swiched off the circuit breaker just to be safe.Then I removed the two mounting screws and disconnected the the element leads. Very easy task, approx 5 mins. THANKS
Was this helpful?
Thank you for voting!
Fridge keeps cycling on and off and a clicking sound happens every time compressor cycles.
10 of 11 people found this instruction helpful.
  • Kirk E from GRASS VALLEY, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
I opened the back panel of the fridge and exposed the compressor. Unplugged existing run capacitor and installed new one with the addition of the sleeve that is stated must be installed around the run capacitor.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I search ed and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.

Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.
Was this helpful?
Thank you for voting!
Light Switch Was Broken
12 of 17 people found this instruction helpful.
  • REY from GAINESVILLE, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
I removed screws that hold cover and put cover aside. I removed the buttons and removed glass cover. I pulled panel out far enough t get tswitch wires and installed switch. Be very careful not to let wires touch metal.
Was this helpful?
Thank you for voting!
Burner heat does not turn down
9 of 9 people found this instruction helpful.
  • Gary from Blanchester, OH
  • Easy
  • 15 - 30 mins
  • Screw drivers
Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio
Was this helpful?
Thank you for voting!
Mistreated Briggs & Stratton 206 CC Engine on MTD Chipper
11 of 15 people found this instruction helpful.
  • Dana from HAMMOND, IN
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
Removed tank and drained old gas.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Was this helpful?
Thank you for voting!
F1 code and oven wouldn't operate
11 of 15 people found this instruction helpful.
  • Robbie from Hillsboro, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on . Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.
Was this helpful?
Thank you for voting!
oven heating/bake element cracked
9 of 10 people found this instruction helpful.
  • Carol from Brunswick, OH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
First-my daughter needed her pizza and I didn't want to even think about the cost of a new range. So she did some research online about replacement parts. Lo an behold, Partselect.com was our answer.

We received the part in a few days and replaced it with just unscrewing a few screws.. AFTER we unplugged the range. We also used a tool that I would describe as a nail remover/lifter to get the end off of the wire connection. Needless to say, we were rookies and had no experience with this type of repair and were so proud that we were able to spend less than $30.00 to fix our oven.
Thanks to Partselect.com for making it easy to do this repair on our own.
Was this helpful?
Thank you for voting!
thermistat and defrost timer
10 of 13 people found this instruction helpful.
  • brad from brenham, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
i have a friend that had a big side by side refrigerator . he had repair man after repairman come and look at it. one thought it was the overload relay in the back and another just said it was compressor problems. this went on for over a month. after all of this and no one able to fix it he went and got another refrigerator . being the ti nker with stuff kind of person i am i said i will come and get the old one to keep him from having to haul it off (he agreed). well i did my home work and tried a few things messing with it. tapping on the thermistat resetting the defrost timer and it dawned on me that that the fridge would run great if i wiggle a wire on the thermistat and reset the defrost timer. so i get on the internet look around for the parts. come to find out they were realy cheap. the day they get here i break out with a screw driver and a nut driver and take the cover off. i take the old parts out and put the new ones in in about 15 minutes. i wiped the inside of the frige clean and pluged it back in. well in no time flat this thing was cooling like a northern blowing through in january. then it dawned on me that i have a 27 cubic ft frige that i didnt pay any thing for (well the 65 bucks i spent on the parts) and it runs great. what a deal.

after getting the big side by side fixed up and running like a champ i realized i have a refrigerator in the garage that my parents gave me a couple of years ago that only ran for a couple of months. well i get brave and decide to try my luck with the second one. due to it sitting up for so long and the humidity i had to do a little more work to it. i replaced a few wires, changed out a couple of connections, put a thermistat , a defrost timer and a evapmotor in it this thing also ran like a champ. i cleaned it up real good ran some steel wool over the outside and sprayed a couple of coats of enamel on it and it looks brand new.

so to end this story i spent about 140 bucks and i have two refrigerators a big side by side ice and water despensing refrigerator in the house and a 17 cubic ft refrigerator in the garage (the wife was happy simply because i had a place to put beer and bait).

if i would have went and purchased both of these refrigerators i would have spent about $1400 for the side by side and about $450 for the other one. man what a bargin, so from now on even if it seems a little dificult i dont get rid of any thing until i give it a good look over and see if i can fix it. i saved a total of $1700 (minus tax).
Was this helpful?
Thank you for voting!
inner glass busted
9 of 11 people found this instruction helpful.
  • robert from orange, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.

Replaced screws and handle,pulled hinge's out to first stop and sli d door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.

PS: shipping was fast and price was great.
Thanks Bob G.
Was this helpful?
Thank you for voting!
1998 oven unit flashing F3
10 of 14 people found this instruction helpful.
  • chris from houston, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.
Was this helpful?
Thank you for voting!
The oven wouldn't heat
8 of 9 people found this instruction helpful.
  • Richard from Wilmington, MA
  • Really Easy
  • Less than 15 mins
  • Pliers
First I shut off the power at the circuit breaker.Then I removed the racks to make room to work.I then removed the 2 screws holding the element in place and pulled both sides out approx.3 inches.After carefully disconnecting the wires,I put the new element in to place and repeated the steps backwards.
Was this helpful?
Thank you for voting!
Original oven light lens had cracked and broken in two.
17 of 36 people found this instruction helpful.
  • Pat from Bucklin, KS
  • Really Easy
  • Less than 15 mins
I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).
Was this helpful?
Thank you for voting!
burner receptacle burned out
8 of 9 people found this instruction helpful.
  • Michael from N. Haverhill, NH
  • Easy
  • 15 - 30 mins
  • Screw drivers
Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.
Was this helpful?
Thank you for voting!
Freezer not getting cold enough to freeze ice cream
8 of 10 people found this instruction helpful.
  • Gary from ROSETO, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Was this helpful?
Thank you for voting!
Burner would only cook on high setting or not heat up at all.
9 of 13 people found this instruction helpful.
  • Judy from West Salem, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.
Was this helpful?
Thank you for voting!
All Instructions for the 3862
46 - 60 of 587