3862 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
F1-1 code
79 of 110 people
found this instruction helpful.
-
charles from marstons mills, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa
... Read more
ilure to do so will cause the plastic plug connector to melt from oven heat.
Read less
Was this helpful?
Thank you for voting!
The original heating element shorted and caught fire
89 of 151 people
found this instruction helpful.
-
Eric from Tooele, UT
- Really Easy
- Less than 15 mins
-
Screw drivers
The repair was simple; I removed just two screws, pulled out the wires, and slipped the two spade connectors off the original element. The repair was simply the reverse of the disassembly. The only thing to remember is to throw the circuit breaker before handling the electrical connectors. Other than that, it couldn't be any more strai
... Read more
ght forward.
Read less
Was this helpful?
Thank you for voting!
Needed to replace oven door gasket.
58 of 69 people
found this instruction helpful.
-
Lori from Scottsdale, AZ
- Really Easy
- Less than 15 mins
-
Pliers
First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.
Was this helpful?
Thank you for voting!
Replaced drip bowls in stove
71 of 134 people
found this instruction helpful.
-
Liza from College Point, NY
- Really Easy
- Less than 15 mins
Took out the old drip bowls and replaced with new bowls.
Other Parts Used:
Was this helpful?
Thank you for voting!
bad light socket
45 of 56 people
found this instruction helpful.
-
nancy from silsbee, TX
- Really Easy
- Less than 15 mins
unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to
... Read more
do it myself. easy easy easy
Read less
Was this helpful?
Thank you for voting!
Burned terminal block and filter board
95 of 208 people
found this instruction helpful.
-
Joseph from Decatur, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench set
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Was this helpful?
Thank you for voting!
Relay
42 of 54 people
found this instruction helpful.
-
John H from Austin, TX
- Really Easy
- 15 - 30 mins
Removed back panel. Opened cover to relay attached to the compressor and pulled off replacing with new relay. No problem.
Better than paying $250 for someone else to do it.
Better than paying $250 for someone else to do it.
Was this helpful?
Thank you for voting!
Rented appartment in which none of the drain pans were the proper size making it very difficult to cook
67 of 131 people
found this instruction helpful.
-
Grace Mary from Canton, OH
- Really Easy
- Less than 15 mins
I removed the element and then the drain pan and replaced with the new correct pans. I replaced the element and all was well.
Other Parts Used:
Was this helpful?
Thank you for voting!
Repeated oven temperature sensor fault codes.
35 of 43 people
found this instruction helpful.
-
David from Arlington, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the righ
... Read more
t side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat the right temperature (you would have to add 100 degrees on to it)
26 of 36 people
found this instruction helpful.
-
Claudine from Bethlehem, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.
Was this helpful?
Thank you for voting!
Built in oven would shut down: fault code F-4
22 of 24 people
found this instruction helpful.
-
Edward from Juliustown, NJ
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set
A few years previously I had this same problem and a PROFESSIONAL had replaced the sensor.
Thus this time I knew what the failure was and obtained the sensor from Part Select. Having observed the PROFESSIONAL replace the sensor before; I followed his easy technec only to learn that when the sensor was pulled from the aft wall of the ... Read more oven that the wires had deteriorated and the plastic plug melted. Therefore it was neccessary to remove the oven from the wall cabinet. Then I removed the panel from the back outside of the oven, cut back the wires and because the kit from Part Select contained additional connectors was able to splice in a replacement connector. Installed the new sensor and reinstalled the oven. LESSON LEARNED; when the PROFESSIONAL had replaced the sensor he had failed to feed the wiring and plug back past the insulated chamber, directly behind the oven, into the cool area assessable by the panel on the aft side of the oven thus the plug and wires were exposed to the heat of the oven. What would commonly be a few minutes job turned into an afternoon project.
Thus this time I knew what the failure was and obtained the sensor from Part Select. Having observed the PROFESSIONAL replace the sensor before; I followed his easy technec only to learn that when the sensor was pulled from the aft wall of the ... Read more oven that the wires had deteriorated and the plastic plug melted. Therefore it was neccessary to remove the oven from the wall cabinet. Then I removed the panel from the back outside of the oven, cut back the wires and because the kit from Part Select contained additional connectors was able to splice in a replacement connector. Installed the new sensor and reinstalled the oven. LESSON LEARNED; when the PROFESSIONAL had replaced the sensor he had failed to feed the wiring and plug back past the insulated chamber, directly behind the oven, into the cool area assessable by the panel on the aft side of the oven thus the plug and wires were exposed to the heat of the oven. What would commonly be a few minutes job turned into an afternoon project.
Read less
Was this helpful?
Thank you for voting!
element went bad..started burning like a weld
20 of 21 people
found this instruction helpful.
-
Randall from Williamsburg, OH
- Really Easy
- Less than 15 mins
-
Screw drivers
Turned off the power at the breaker box. Removed the two screws, pulled the element out about 3 inches, disconnected the two wires, reconnected the two wires to the new element, inserted element back into place, screwed in the screws...all finished...works great! Delivery was super fast...just a great experience all the way around.
Was this helpful?
Thank you for voting!
This refrigerator had pawer( lite was on) but nothing turning--motor or fan. Turned control temperature min-max - no cange.
49 of 112 people
found this instruction helpful.
-
HAE-YOUNG from Douglaston, NY
- Easy
- 1- 2 hours
-
Screw drivers
Found burned Defrost timer contacts.
Was this helpful?
Thank you for voting!
Oven failed to maintain the set temperature.
18 of 19 people
found this instruction helpful.
-
Thomas from Clarksville, MD
- A Bit Difficult
- 15 - 30 mins
-
Socket set
Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the bac ... Read more kside of the insulation. Assembled the two screws and tightened.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the bac ... Read more kside of the insulation. Assembled the two screws and tightened.
Read less
Was this helpful?
Thank you for voting!
bake element cracked
19 of 24 people
found this instruction helpful.
-
Ruth from Moyock, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
Being a woman, I first cleaned the oven. Removed two screws holding the element in place. Pulled element out about 3 inches and disconnected one clip attached to a yellow wire another clip attached to a green wire. Put new element in connected clips. Replaced screws.
Was this helpful?
Thank you for voting!