3860X Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Baking element burned out
2 of 2 people
found this instruction helpful.
-
Stephen from Pleasant Hill, IA
- Easy
- Less than 15 mins
-
Screw drivers
I watched the video on the web site and it worked like a dream. Two screws to take out - disconnect wires put back connecting wires and replace the screws again. Just like the video. Thanks
Was this helpful?
Thank you for voting!
Drip pans were not original to range, I could not get them clean.
2 of 2 people
found this instruction helpful.
-
Lynn from BRADENTON, FL
- Really Easy
- Less than 15 mins
I reoved old drip pans and installed new ones. Very easy, they look great!
Other Parts Used:
Was this helpful?
Thank you for voting!
The element on my 20+ year old Jenn Zaire oven had broken in two...
2 of 2 people
found this instruction helpful.
-
Mary from New Britain, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
Went online to find replacement part. (Because I’m cheap) Came across the website, found the part by model number, and watched the wonderful replacement video that was right on the same page as the part. After the part arrived, (in just a couple of days) I put the new one in. Only took a couple of minutes! Perfection! Thanks for making m
... Read more
y problem, no problem at all!
Read less
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
left cover for the oven light broke when trying to replace the bulb
2 of 2 people
found this instruction helpful.
-
Mark from SHOREVIEW, MN
- Very Easy
- Less than 15 mins
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
Was this helpful?
Thank you for voting!
Used part
2 of 3 people
found this instruction helpful.
-
Sabrina from FREMONT, CA
- Very Easy
- Less than 15 mins
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Other Parts Used:
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people
found this instruction helpful.
-
Rhoda P. from Secaucus, NJ
- Really Easy
- Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Other Parts Used:
Was this helpful?
Thank you for voting!
The oven glass shattered when I dropped water in the heated Glass
2 of 3 people
found this instruction helpful.
-
Franziska from Salt Lake City, UT
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order..
The last time this happened to me(!!) I brought the door to a repair man and hadto pa ... Read more y 200 dollars , I saved 150 Dollars doing it myself!
The last time this happened to me(!!) I brought the door to a repair man and hadto pa ... Read more y 200 dollars , I saved 150 Dollars doing it myself!
Read less
Was this helpful?
Thank you for voting!
Broken glass in oven door
3 of 6 people
found this instruction helpful.
-
Jamie from Hoover, AL
- Easy
- 30 - 60 mins
-
Screw drivers
Disassembled the oven door, removed broken glass, replaced with new glass and reassembled oven door. Took very little time. Online diagram on this site helped to keep everything in order and easily know what part was needed. Thanks!!!!
Was this helpful?
Thank you for voting!
Frayed and exposed receptical wires in cartridge
2 of 3 people
found this instruction helpful.
-
Richard C from San Jose, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
Read less
Was this helpful?
Thank you for voting!
The bake element burst.
1 person
found this instruction helpful.
-
Diane from Littleton, CO
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the two screws that held the element in place and then pulled off the element from the connectors. Slipped the new connectors on. Tested the oven - Baked some blackberry cobbler!
Was this helpful?
Thank you for voting!
Oven baking coil had burned out
1 person
found this instruction helpful.
-
Marie from Fredericksburg, VA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Removed two screws from back of oven ,pulled apart old coil from wires, inserted new coil into the small metal pieces, pushed back and screws replaced. Really easy , anyone can do. Oh, I am 70 years old so probably people younger could do more quickly.
Was this helpful?
Thank you for voting!
Wife said stove was on fire - Oven element shorted.
1 person
found this instruction helpful.
-
James from Hoyt Lakes, MN
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the old element by removing 2 screws and disconnecting two solderless connectors. One solderless connector was melted in two. I had to remove the rear panel and cut the old connector off and crimped on a new solderless connector. The time required was lengthened due to trip to the hardware store to get a new connector. While I was
... Read more
fixing the oven element my wife replaced the oven light.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Inner most oven door was broken.
1 person
found this instruction helpful.
-
William from WASHINGTON, DC
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
I followed peoples instructions here, and it was not very difficult.
Was this helpful?
Thank you for voting!
Oven door hinges broken
4 of 10 people
found this instruction helpful.
-
Brian from Lakewood, CO
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers
With the back removed, replacing the lamp receptacle is straight-forward. Likewise, the door gasket is very easy. However, in order to replace the hinges, you have to remove the burner glass top (screws underneath the front lip), and inner and outer side panels. Also the supplied hinges mounting holes were not threaded so I had to use my
... Read more
own bolts, lock-washers and nuts in order to attach them. Total time, including a bit of cleaning, was 5 hours.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!