3848 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer stopped working
9 of 13 people
found this instruction helpful.
-
Clifford from Melbourne, FL
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
I noticed that if I unplugged the refrigerator and plugged it back in a while later it would start working but eventually would stop. I deduced the problem was likely the defrost thermostat. I ordered the thermostat but it was in a difficult place behind the evaporator coil which I could not remove. While I was trying to work it into posi
... Read more
tion my hand pressed against the defrost coil and shattered the glass sheath. I ordered the coil and finally managed to get it and the thermostat installed. The refrigerator seems to work fine now.
Read less
Was this helpful?
Thank you for voting!
Refridgerator wouldn't cycle into defrost mode without doing it manually.
9 of 14 people
found this instruction helpful.
-
Ben from Warrior, AL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed
... Read more
to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !
Read less
Was this helpful?
Thank you for voting!
Noisy fan in freezer compartment
6 of 6 people
found this instruction helpful.
-
Jeffrey B from Lewiston, ME
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed shelf by pushing to left and lifting up on RH end. Removed screws in plastic cooling tower and slid tower up. Pulled back wall of freezer compartment out, RH side first. Removed two screws from fan bracket, unplugged fan wiring harness by compressing connector spring clips and pulling joint apart. Pulled fan blade off (note locati
... Read more
on of blade on shaft for reinstall alignment purposes), removed both green grommets.Then just reinstalled new items.My philosphy on repairs of this nature is to replace all related parts that could be contributing to problem. The parts are cheap compared to the aggravation and inconvenience of doing the repair several times until you fix the problem. You don't need to purchase the compression ring if you buy the fan blade as it has one already installed on it. Problem solved, though now that the noise is gone am hearing fainter similar noises from lower fan. Should I be surprised, both fans are of similar design.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
compressor not starting
9 of 15 people
found this instruction helpful.
-
H.K. from Seagoville, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Refrigerator is not cooling. Light and fan working. Changed the capacitor.. Still not cooling. Back to discovery mode.It may be the timer
Certainly not PartSelect's fault. They have great service.
Certainly not PartSelect's fault. They have great service.
Was this helpful?
Thank you for voting!
refrigerator wasn't cooling but the freezer was working properly
6 of 6 people
found this instruction helpful.
-
Don from BELLVILLE, TX
- Very Easy
- 15 - 30 mins
-
Nutdriver
From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then
... Read more
another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.
Read less
Was this helpful?
Thank you for voting!
no problem
7 of 10 people
found this instruction helpful.
-
hung from herndon, VA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The part i received fit perfect, i just removed the old part and put the new part in with the screw driver.Really easy
Other Parts Used:
Was this helpful?
Thank you for voting!
Door gasket was cracked and coming off
5 of 5 people
found this instruction helpful.
-
Mark from SALISBURY, MD
- Really Easy
- 15 - 30 mins
-
Socket set
Took freezer door off with torque screwdriver, unscrewed freezer door/refrigerator hinge with 3/8 socket. Removed refrigerator door and put on kitchen table. (Turn refrigerator off temporarily). Put freezer door back on temporarily. Pull out old gasket from groove on door. Put in new gasket. Take freezer door back off, put on refrigerator
... Read more
door, hinge, freezer door, put torque screws back in, your done. (Turn fridge back on)
Read less
Was this helpful?
Thank you for voting!
Refrigerator to warm
5 of 5 people
found this instruction helpful.
-
Lloyd from PITTSBURG, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long
Was this helpful?
Thank you for voting!
light not working
7 of 11 people
found this instruction helpful.
-
robert from FRANKLIN SQ, NY
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.
Was this helpful?
Thank you for voting!
Plastic frame was broken
5 of 5 people
found this instruction helpful.
-
Sandra from YUMA, AZ
- Very Easy
- Less than 15 mins
I removed the broken frame, glass, and bins from the refrigerator, cleaned the area, put the new frame in place making sure it was fitted into the brackets securely, and replaced the glass and bins into their proper slots.
Was this helpful?
Thank you for voting!
Fan was making annoying noise and rubbing against the frame of opening.
6 of 8 people
found this instruction helpful.
-
Tony from Los Angeles, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers, Socket set
Removed old fan and replaced the fan with new one.
2 years ago, the refrigerator was under warranty and tech replaced the fan but I found that the fan was not the original spec fan. Apparently, the fan that the tech replaced did not fit opening.
Now, my refrigerator works no problem. Save a ton of $$$ by doing it myself. ... Read more Do not have to buy a new fridge and this one works perfect.
2 years ago, the refrigerator was under warranty and tech replaced the fan but I found that the fan was not the original spec fan. Apparently, the fan that the tech replaced did not fit opening.
Now, my refrigerator works no problem. Save a ton of $$$ by doing it myself. ... Read more Do not have to buy a new fridge and this one works perfect.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
A rat had chewed half of all four blades off
9 of 18 people
found this instruction helpful.
-
Curtis from Dothan, AL
- Really Easy
- Less than 15 mins
-
Nutdriver
First I removed the left condensor fan motor bracket nut, loosened the right motor bracket, dropped the moter bracket down freeing the motor from the rubber grommets.
Pulled the fan off from the motor shaft, pressed the new fan on the shaft and installed new grommets. Replaced the motor bracket and tightened the right bracket nut an ... Read more d checked fan for clearance and free spin. Reinstaled the left bracket nut. Turned on the refrigerator and checked fan for action. Everything worked great.
I did not know the fan replacement came with a compression ring already installed, so now I have an extra compression ring.
Pulled the fan off from the motor shaft, pressed the new fan on the shaft and installed new grommets. Replaced the motor bracket and tightened the right bracket nut an ... Read more d checked fan for clearance and free spin. Reinstaled the left bracket nut. Turned on the refrigerator and checked fan for action. Everything worked great.
I did not know the fan replacement came with a compression ring already installed, so now I have an extra compression ring.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The old plastic slide broke from hanging too much weight on it.
5 of 6 people
found this instruction helpful.
-
Terrence M from Portsmouth, NH
- Really Easy
- 15 - 30 mins
First I had to go to the hardware store to buy a star bit to remove the old screws ($1.09). I attached it to my quarter-inch drill and used it to remove the old screws. I then used those same screws to attach the new slide. Once I had the star bit, it was little more than a five-minute task.
Was this helpful?
Thank you for voting!
Bad defrost timer
5 of 7 people
found this instruction helpful.
-
Bruce from Silver Spring, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers
Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.
I'll be back...
I'll be back...
Was this helpful?
Thank you for voting!
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
5 of 7 people
found this instruction helpful.
-
Rickey from DUMAS, AR
- Really Easy
- 30 - 60 mins
-
Socket set
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugge
... Read more
d it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Read less
Was this helpful?
Thank you for voting!