3848 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Existing light switch was hard to remove.
14 of 19 people
found this instruction helpful.
-
Stephen from Jupiter, FL
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.
Was this helpful?
Thank you for voting!
old gasket was worn and torn
12 of 14 people
found this instruction helpful.
-
Barbara from Key West, FL
- Really Easy
- Less than 15 mins
The new gasket was a little out of shape, because of the way it had to be shipped, however, I unpacked it, shaped it like it should have been, and just let it sit for a few days. Time to install the gasket and it was so easy...just popped out the old one and slipped in the new one, and it is working perfectly.
Thanks so much
Thanks so much
Was this helpful?
Thank you for voting!
COLD FREEZER WARM FRIG
13 of 17 people
found this instruction helpful.
-
Richard from LONG BEACH, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
After several defrost sessions I realized we had a component problem. Freezer and frig would cool up and maintain for a week or so but then the frog would go warm and the freezer would be ice cold. SO it was then I knew it was a defrost sequence matter. Thanks to Parts Select and their part to culprit algorithm it provided me the several
... Read more
most likely parts to be at fault. Since not having a voltage tester it was R/R time so I started with defrost timer and then went on from there. So all in told the bill for parts was around $120 still cheaper than a repair service call and obviously buying a new unit. Replacing the parts was simple, the most difficult being the defrost heater element but nothing to throw your hands up. My advice is just stay patient, do plenty of research and tackle it, you will save hundreds of dollars. Living without a frig for several days can be uncomfortable but I was absolutely determined to salvage the frig and save money and it was all worth it.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
botton half of refrigerator not cooling
25 of 55 people
found this instruction helpful.
-
HANCEL from ELMONT, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
easy as 1.2.3 remove and replace before even thinking. just to let you know i also do this for a living but it is one of the most difficult thing when you have to stop and fix your own
Was this helpful?
Thank you for voting!
Interior light needed replaced
22 of 46 people
found this instruction helpful.
-
Leo from TWIN FALLS, ID
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Was this helpful?
Thank you for voting!
Refrigerator section not cold, freezer section cold
10 of 10 people
found this instruction helpful.
-
David from Shalimar, FL
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
Based on the relatively young age of refrigerator, I suspected the defroster electrical circuit. The evaporator core in the freezer was frozen solid, which confirms that the defrost heater circuit is not working. Thawed out (with a hot air gun) and disassembled the freezer section to access the evaporator core and defrost heater. If yo
... Read more
u have an ice maker, you will have to remove it to disassemble the freezer section. Confirmed with a voltmeter and ammeter that the defrost heater was not getting voltage. When the defrost heater is working, it will glow with an orange color. Also confirmed with a voltmeter that the defrost timer, located in the refrigerator section was working correctly. You can use a common blade screwdriver to rotate the timer through the cold and defrost cycles. Finally, I determined with a voltmeter and ammeter that the defrost thermostat, located on the evaporator core was not switching the defrost heater voltage. Ordered a new thermostat ($12) from this website and installed it. Refrigerator is as good as new. Be careful, there are many electrical hazards during the troubleshooting phase. Safety first.
Read less
Was this helpful?
Thank you for voting!
Fridge keeps cycling on and off and a clicking sound happens every time compressor cycles.
10 of 11 people
found this instruction helpful.
-
Kirk E from GRASS VALLEY, CA
- Easy
- Less than 15 mins
-
Screw drivers
I opened the back panel of the fridge and exposed the compressor. Unplugged existing run capacitor and installed new one with the addition of the sleeve that is stated must be installed around the run capacitor.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I search ... Read more ed and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.
Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I search ... Read more ed and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.
Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.
Read less
Was this helpful?
Thank you for voting!
freezer wouldn't defrost & fridge wouldn't cool.
11 of 14 people
found this instruction helpful.
-
sherri from hamilton, IA
- Really Easy
- 30 - 60 mins
-
Nutdriver
First, using a nut driver, I removed icemaker and back panel inside freezer. I unhooked the wire connectors at each end of the heater defrost element and replaced with new element. I reinstalled the back panel and the icemaker.
Second, using the same nut driver I removed the casing located inside fridge on the top. I pulled the casin ... Read more g down & unhooked the wiring harness. I removed the control temp switch which was held in by two clips. I replaced with new switch, plugged harness back in, reinstalled casing and BINGO....it is as good as new....beats buying a new refrigerator anyday!!!!
THANK YOU Bernard S.!!!!!!!!!!!!!!
Sincerely,
Mom of three boys
Second, using the same nut driver I removed the casing located inside fridge on the top. I pulled the casin ... Read more g down & unhooked the wiring harness. I removed the control temp switch which was held in by two clips. I replaced with new switch, plugged harness back in, reinstalled casing and BINGO....it is as good as new....beats buying a new refrigerator anyday!!!!
THANK YOU Bernard S.!!!!!!!!!!!!!!
Sincerely,
Mom of three boys
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Switchlight was broken on tennant's refridge
10 of 12 people
found this instruction helpful.
-
Mark from Somers Point, NJ
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapp
... Read more
ed the new switch into place.
10 minutes total.
10 minutes total.
Read less
Was this helpful?
Thank you for voting!
Twice I ordered the oven light bulb & each time the light bulb was defected
18 of 38 people
found this instruction helpful.
-
Barbara from BELLEVUE, WA
- Very Difficult
- Less than 15 mins
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl
... Read more
iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Read less
Was this helpful?
Thank you for voting!
Ice in freezer running down sides
8 of 9 people
found this instruction helpful.
-
P. Michael from Tustin, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
This is a built-in unit. Remove the external bezel at the top of the unit. Reach through the unit and unplug the frig. On the compressor unit, you'll see a vertical metal panel. Remove the metal panel and the timer is right behind it. Remove one wire at a time and switch it to the new timer. Remove timer and replace with new one.
... Read more />
Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.
... Read more />
Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.
Read less
Was this helpful?
Thank you for voting!
Overload switch failed on compressor. No cooling
8 of 9 people
found this instruction helpful.
-
phillip from hartselle, AL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unplug. Remove back cover. Remove retainer (simple wire clip) from overload. Unplug overload from compressor. Remove two power wires (if stabs are tight you might need pliers). Note which wire goes where. Remove capacitor from overload (just pul it straight out .. Pull hard or pry a little with screwdriver. Insert capacitor into new switc
... Read more
h. Reattach wires to same place in switch. Insert switch into compressor. Replace retainer clip. Replace rear cover with original screws. Plug in. Cool!
Read less
Was this helpful?
Thank you for voting!
defrost system kept freezing up
8 of 10 people
found this instruction helpful.
-
Robert from Williamstown, NY
- Easy
- 15 - 30 mins
-
Screw drivers
took out 4 screws - lowered timer cover - replaced timer- put it back together
Was this helpful?
Thank you for voting!
Freezer not getting cold enough to freeze ice cream
8 of 10 people
found this instruction helpful.
-
Gary from ROSETO, PA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Read less
Was this helpful?
Thank you for voting!
Poor cooling, running all the time
12 of 22 people
found this instruction helpful.
-
MICHAEL from ALEXANDRIA, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed two screws holding the cover. Unclipped and unplugged the defroster timer. Plugged in the new one . Replaced the cover. Finished.
Was this helpful?
Thank you for voting!