3845 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
loud noise when running
30 of 36 people
found this instruction helpful.
-
joseph from phillipsburg, NJ
- Easy
- 30 - 60 mins
-
Screw drivers
took off back cover 6 screws unpluged wire conecter( hardest part to do )took 2 screws out of mounting bracket pulled fan blade off replaced motor and gromets reverse to reasmble
Other Parts Used:
Was this helpful?
Thank you for voting!
Light switch inside refrigerator wasn't working
31 of 43 people
found this instruction helpful.
-
Erick from Elmhurst, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First turned off power and removed top shelf.
Then I used a flathead to slowly pry the switch out by the two sides. You just anlge ita bit and it slideds out easily. Then I disconnected the wires from the old switch, connected the new one and installed the new switch by snapping it back into the cutout.
Then I used a flathead to slowly pry the switch out by the two sides. You just anlge ita bit and it slideds out easily. Then I disconnected the wires from the old switch, connected the new one and installed the new switch by snapping it back into the cutout.
Other Parts Used:
Was this helpful?
Thank you for voting!
Everything was freezing in the bottom and top
26 of 29 people
found this instruction helpful.
-
Thomas from Germantown, TN
- Very Easy
- Less than 15 mins
-
Screw drivers
Pulled out the control sensor on the ceiling of the fridge. (2 screws) Took a picture with phone on how everything was installed. Unplugged all wires and pulled out Control Temp sensor. Installed new one and attached all wires. Installed back in fridge and plugged it back in. Everything works like new.
Was this helpful?
Thank you for voting!
The lower half of the refrigerator was not cold, the fan was not blowing
27 of 34 people
found this instruction helpful.
-
Lucinda from Yucca, AZ
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the 4 screws in the back of the freezer. I then pulled the connection from the fan , I replaced the fan to the connection, replaced the 4 screws and I was done! I still can't believe how simple it was.
Was this helpful?
Thank you for voting!
refrigerator would not defrost
21 of 23 people
found this instruction helpful.
-
Donald from worthington, OH
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Look were timer was located, in my refigerator is next to the dial to ajust the temperature. used a screwdriver to get panel off. replaced timer then used a straight screwdriver to advance timer to turn on compessor . monitor temperature . checked out.
Was this helpful?
Thank you for voting!
Ice built up on coils. Fridge was warm.
21 of 24 people
found this instruction helpful.
-
Neil from Boise, ID
- Difficult
- 1- 2 hours
-
Nutdriver, Pliers
No instructions came with new parts. Access to element was impossible until I accidentally discovered that the two styrofoam cushions at the ends of the coils were removable. Once removed, access to the heater and thermostat was very easy.
Unplug appliance, remove freezer shelf, cold air ducts, back of freezer, disconnect lig ... Read more ht, (My model does not have ice maker. This may also need to be disconnected.)
1.Remove styrofoam cushions at end of coils
2.Locate element between bottom two coils
3.Disconnect the male/female connections
4.Remove support clip under center of element
5.Remove element
6.Replace new element in reverse
Connecting the thermostat wires was challenging because they were somewhat behind the coils.
1.With styrofoam removed, unclip thermostat from coil
2.Carefully cut wires (leave enough to connect new wires)
3.Connect new thermostat wires (color of wires matched on my fridge)
4.Clip new thermostat in place
5.Replace styrofoam
6.Button it all up
With these steps, this job would take maybe 30 minutes; somewhat longer if your model has an icemaker.
Hope this helps.
Unplug appliance, remove freezer shelf, cold air ducts, back of freezer, disconnect lig ... Read more ht, (My model does not have ice maker. This may also need to be disconnected.)
1.Remove styrofoam cushions at end of coils
2.Locate element between bottom two coils
3.Disconnect the male/female connections
4.Remove support clip under center of element
5.Remove element
6.Replace new element in reverse
Connecting the thermostat wires was challenging because they were somewhat behind the coils.
1.With styrofoam removed, unclip thermostat from coil
2.Carefully cut wires (leave enough to connect new wires)
3.Connect new thermostat wires (color of wires matched on my fridge)
4.Clip new thermostat in place
5.Replace styrofoam
6.Button it all up
With these steps, this job would take maybe 30 minutes; somewhat longer if your model has an icemaker.
Hope this helps.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud freezer fan motor
21 of 25 people
found this instruction helpful.
-
William from GENEVA, OH
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed old worn out freezer fan motor and replaced with a new one. Piece of cake. Sooo easy and saved money too!
Other Parts Used:
Was this helpful?
Thank you for voting!
it quit working-refer-freezer-part,fan keeped running
21 of 25 people
found this instruction helpful.
-
jim from buckeye, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver
pulled out switchs verified part #'s-ordered replacements- its actually plug in switches and very simple
Other Parts Used:
Was this helpful?
Thank you for voting!
The Crisper Glass Shelf Broke
23 of 31 people
found this instruction helpful.
-
Marci from Cedar City, UT
- Really Easy
- Less than 15 mins
The Crisper Glass Shelf Broke. My son removed it to clean and dropped the shelf. I ordered a replacement shelf which arrived in record time and just slid it into place.
Was this helpful?
Thank you for voting!
Refrigerator door handle broke
21 of 26 people
found this instruction helpful.
-
Barbara from Philadelphia, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Simply removed the screws and pulled the old handle off and aligned the new handle with the holes and replaced the two screws.
Was this helpful?
Thank you for voting!
This refrigerator had pawer( lite was on) but nothing turning--motor or fan. Turned control temperature min-max - no cange.
49 of 112 people
found this instruction helpful.
-
HAE-YOUNG from Douglaston, NY
- Easy
- 1- 2 hours
-
Screw drivers
Found burned Defrost timer contacts.
Was this helpful?
Thank you for voting!
The refrigirator light would not come on.
26 of 44 people
found this instruction helpful.
-
Jania from Novato, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.
Was this helpful?
Thank you for voting!
The drawers and shelf in my refrigerator broke
21 of 31 people
found this instruction helpful.
-
ROSANNE from HAZLE TOWNSHIP, PA
- Really Easy
- Less than 15 mins
I ordered new ones The came really fast. One was broken . My exchange was handled with great speed and excellent customer care.
Other Parts Used:
Was this helpful?
Thank you for voting!
Refrigerator fan motor died
16 of 18 people
found this instruction helpful.
-
Kevin A. from CONCORD, NH
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Socket set
It has been my experience that these motors sometimes die when the refrigerator is overfilled and motor strains to keep refrigerator cold. And this motor is used in several models of refrigerators. That said, sometimes the hook-up is slightly different between other units. The available video is good, but like I said, circumstances wil
... Read more
l be slightly different between various models.
After cleaning out freezer (plug disconnected first), start to remove outer plastic covers. If you want to keep track of the different steps, you can take pictures with your cellphone. And if there are any connecting wire attachments you think you might not remember, again, you can take a picture, or label with tape (colored tape, or by writing on the tape). And for keeping track of the different-size screws, I place them in a muffin tin, keeping an order of left to right and top to bottom in the tin. When removing Styrofoam blocks in bottom center, make sure you remove any remaining ice underneath in the hole so refrigerator can "breathe". Freezer air is moved below to refrigerator compartment, so a blocked vent hole will strain refrigerator as it tries to maintain its temperature setting and can be the cause of your failed motor.
After replacing motor onto bracket with grommets and blade, don't completely tighten. Position plastic cover with hole opening over motor and blade assembly. Twirl motor blade to see if there is any interference with cover. If not, take away cover and tighten motor on bracket. If there is any rubbing, adjust motor/blade assembly accordingly before tightening in place. Putting everything back together is in reverse order.
After cleaning out freezer (plug disconnected first), start to remove outer plastic covers. If you want to keep track of the different steps, you can take pictures with your cellphone. And if there are any connecting wire attachments you think you might not remember, again, you can take a picture, or label with tape (colored tape, or by writing on the tape). And for keeping track of the different-size screws, I place them in a muffin tin, keeping an order of left to right and top to bottom in the tin. When removing Styrofoam blocks in bottom center, make sure you remove any remaining ice underneath in the hole so refrigerator can "breathe". Freezer air is moved below to refrigerator compartment, so a blocked vent hole will strain refrigerator as it tries to maintain its temperature setting and can be the cause of your failed motor.
After replacing motor onto bracket with grommets and blade, don't completely tighten. Position plastic cover with hole opening over motor and blade assembly. Twirl motor blade to see if there is any interference with cover. If not, take away cover and tighten motor on bracket. If there is any rubbing, adjust motor/blade assembly accordingly before tightening in place. Putting everything back together is in reverse order.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Lower part of refrigerator warm
16 of 19 people
found this instruction helpful.
-
bernard from Katonah, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Pulled refrigerator plug from socket.
Removed all freezer items. Put them into sink to keep cool.
Phillips head screwdriver removed screws from plastic housing fan cover from rear of freezer compartment.
Removed fan housing panel by lifting up and out. Panel has two small tabs that fit into back panel.
Removed back pan ... Read more el with phillips head screwdriver.
Fan is now exposed. Not working.
Plugged power cord back in.
Disconnected power adapter to fan.
Voltage meter sees power to ground and hot wire.
Fan not working
Unplugged power cord.
Removed fan from rear by socket tool.
Used hair dryer to remove ice build up in styrofoam insert between freezer compartment and lower section.
Removed foam insert....broke a couple of pieces off.
Test new motor with a line cord wire stripped at ends
Motor works. (Old one did not work with same test)
Replaced fan into bracket.
Replaced bracket into rear of freezer.
Plugged power cord in.
Fan does not work.....Whoa!!!..closed freezer door and heard fan running!!! It works.
Replaced everything...foam insert, panels, food.
One week later, still working.....
(Now...I don't know why the fan did not start right away...it may be that there's a small round thermostat sitting on a copper tubing, that needed some time to kick in...but that's a supposition.)
Have fun
Removed all freezer items. Put them into sink to keep cool.
Phillips head screwdriver removed screws from plastic housing fan cover from rear of freezer compartment.
Removed fan housing panel by lifting up and out. Panel has two small tabs that fit into back panel.
Removed back pan ... Read more el with phillips head screwdriver.
Fan is now exposed. Not working.
Plugged power cord back in.
Disconnected power adapter to fan.
Voltage meter sees power to ground and hot wire.
Fan not working
Unplugged power cord.
Removed fan from rear by socket tool.
Used hair dryer to remove ice build up in styrofoam insert between freezer compartment and lower section.
Removed foam insert....broke a couple of pieces off.
Test new motor with a line cord wire stripped at ends
Motor works. (Old one did not work with same test)
Replaced fan into bracket.
Replaced bracket into rear of freezer.
Plugged power cord in.
Fan does not work.....Whoa!!!..closed freezer door and heard fan running!!! It works.
Replaced everything...foam insert, panels, food.
One week later, still working.....
(Now...I don't know why the fan did not start right away...it may be that there's a small round thermostat sitting on a copper tubing, that needed some time to kick in...but that's a supposition.)
Have fun
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!