3841 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fridge doesn't cool properly; freezer iced up
4 of 5 people
found this instruction helpful.
-
Will from Houston, TX
- Easy
- 15 - 30 mins
-
Nutdriver
You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.
Was this helpful?
Thank you for voting!
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people
found this instruction helpful.
-
Lee from OZARK, AR
- Really Easy
- 30 - 60 mins
-
Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re
... Read more
placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Read less
Was this helpful?
Thank you for voting!
door seal contaminated by a boil-over, not flexible
3 of 3 people
found this instruction helpful.
-
Rob from Yakima, WA
- Really Easy
- Less than 15 mins
From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.
Was this helpful?
Thank you for voting!
Old element caught fire, replaced with new one
3 of 3 people
found this instruction helpful.
-
louis from CAHOKIA, IL
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed screws of old element pulled clips off replaced with new element very easy
Was this helpful?
Thank you for voting!
Gasket was worn out.
3 of 3 people
found this instruction helpful.
-
Michael from VALLEJO, CA
- Really Easy
- Less than 15 mins
-
Pliers
Put a new one in.
Was this helpful?
Thank you for voting!
Oven heat loss, door gasket needed replacement
3 of 4 people
found this instruction helpful.
-
Stephen from Chapell Hill, NC
- Really Easy
- Less than 15 mins
The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in plac
... Read more
e! Simple!
Read less
Was this helpful?
Thank you for voting!
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
3 of 4 people
found this instruction helpful.
-
George from Irving, TX
- Really Easy
- Less than 15 mins
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Other Parts Used:
Was this helpful?
Thank you for voting!
drain freezing up found cond fan not working
3 of 4 people
found this instruction helpful.
-
glenn from la harpe, KS
- Really Easy
- Less than 15 mins
Cleaned oh t freezer removed floor. Removed back inside wall removed and replaced fan and put back removed parts
L
L
Was this helpful?
Thank you for voting!
was not defrosting
3 of 4 people
found this instruction helpful.
-
denis from freedom, NH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom
Was this helpful?
Thank you for voting!
one electric burner does not get hot
5 of 10 people
found this instruction helpful.
-
dinh from austin, TX
- Easy
- 15 - 30 mins
-
Screw drivers
swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. U
... Read more
sed the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.
Read less
Was this helpful?
Thank you for voting!
Burner wouldn't heat (wiring failure)
3 of 4 people
found this instruction helpful.
-
Eugene from San Antonio, TX
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench set
1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These ... Read more are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These ... Read more are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
Read less
Was this helpful?
Thank you for voting!
Bake Element wouldn't heat up to temperature
2 of 2 people
found this instruction helpful.
-
John from Foxboro, MA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
I had viewed the video link on PartsSelect. I removed 2 screws and proceeded to pull element out to disconnect wire connectors. However one side the wire connected was melted on to the contact tab of the element and the wire was broken off. I proceeded to remove back panel from stove and located the exposed broken wire. I stripped back wi
... Read more
re and installed a new wire connector that I had in my tool box. I fed wire through small hole. Then I re-installed back panel. I then connected wires to the new bake element and installed element mounting screws.
Read less
Was this helpful?
Thank you for voting!
Burner control knob/switch shaft had broken off.
4 of 8 people
found this instruction helpful.
-
Steve from San Luis Obispo, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.
Was this helpful?
Thank you for voting!
replaced old drip pans
3 of 5 people
found this instruction helpful.
-
Frances from Summerfield, FL
- Really Easy
- Less than 15 mins
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!
Other Parts Used:
Was this helpful?
Thank you for voting!
The element on my 20+ year old Jenn Zaire oven had broken in two...
2 of 2 people
found this instruction helpful.
-
Mary from New Britain, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
Went online to find replacement part. (Because I’m cheap) Came across the website, found the part by model number, and watched the wonderful replacement video that was right on the same page as the part. After the part arrived, (in just a couple of days) I put the new one in. Only took a couple of minutes! Perfection! Thanks for making m
... Read more
y problem, no problem at all!
Read less
Was this helpful?
Thank you for voting!