EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3822 - Instructions

All Instructions for the 3822
61 - 75 of 405

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner control knob/switch shaft had broken off.
4 of 8 people found this instruction helpful.
  • Steve from San Luis Obispo, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.
Was this helpful?
Thank you for voting!
oven light glass cover was broken
2 of 2 people found this instruction helpful.
  • wayne from LIMINGTON, ME
  • Really Easy
  • 15 - 30 mins
took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.
Was this helpful?
Thank you for voting!
left cover for the oven light broke when trying to replace the bulb
2 of 2 people found this instruction helpful.
  • Mark from SHOREVIEW, MN
  • Very Easy
  • Less than 15 mins
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
Was this helpful?
Thank you for voting!
Drip pans were not original to range, I could not get them clean.
2 of 2 people found this instruction helpful.
  • Lynn from BRADENTON, FL
  • Really Easy
  • Less than 15 mins
I reoved old drip pans and installed new ones. Very easy, they look great!
Was this helpful?
Thank you for voting!
Bake element caught on fire
2 of 2 people found this instruction helpful.
  • Dan from TomRriver, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I got the run around about my HARWICK stove at several part stores. Like they all said the same thing (cant look it up just bring it down) So i did and then they would say, what's the model number. ERR! SO my wife found parts select on the web and they beat the three price quotes I got. First turn the power off to the stove!!! The repair was simple. Just remove the two screws on both side's and pull the element out but just enough for the wire's to show. Disconnect the two wire's and pull the element out. Reverse the processes but when wire's are reconnected squeeze terminals end gently to ensure a good connection. This is a great company to deal with, I will be using them again. Thanks and good luck!!!
Was this helpful?
Thank you for voting!
replaced old drip pans
3 of 5 people found this instruction helpful.
  • Frances from Summerfield, FL
  • Really Easy
  • Less than 15 mins
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Baking element burned out
2 of 2 people found this instruction helpful.
  • Stephen from Pleasant Hill, IA
  • Easy
  • Less than 15 mins
  • Screw drivers
I watched the video on the web site and it worked like a dream. Two screws to take out - disconnect wires put back connecting wires and replace the screws again. Just like the video. Thanks
Was this helpful?
Thank you for voting!
Bake Element wouldn't heat up to temperature
2 of 2 people found this instruction helpful.
  • John from Foxboro, MA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
I had viewed the video link on PartsSelect. I removed 2 screws and proceeded to pull element out to disconnect wire connectors. However one side the wire connected was melted on to the contact tab of the element and the wire was broken off. I proceeded to remove back panel from stove and located the exposed broken wire. I stripped back wi re and installed a new wire connector that I had in my tool box. I fed wire through small hole. Then I re-installed back panel. I then connected wires to the new bake element and installed element mounting screws.
Was this helpful?
Thank you for voting!
Frayed and exposed receptical wires in cartridge
2 of 3 people found this instruction helpful.
  • Richard C from San Jose, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridg e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.
Was this helpful?
Thank you for voting!
needed to replace stove pans and burner
3 of 6 people found this instruction helpful.
  • Marylou from Sitka, AL
  • Really Easy
  • Less than 15 mins
An easy replacement job.

Service from you was prompt and the replacement parts arrived in perfect condition...thanks
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people found this instruction helpful.
  • Rhoda P. from Secaucus, NJ
  • Really Easy
  • Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Was this helpful?
Thank you for voting!
Used part
2 of 3 people found this instruction helpful.
  • Sabrina from FREMONT, CA
  • Very Easy
  • Less than 15 mins
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Was this helpful?
Thank you for voting!
Element didn't heat at all
1 person found this instruction helpful.
  • Roger from PATERSON, NJ
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Removed 2 screws, disconnected wires, attached wires to new element, put screws back. Turned oven on. Perfect.
Was this helpful?
Thank you for voting!
The Baking Element won't heat to bake.
1 person found this instruction helpful.
  • Kiara from JACKSONVILLE, FL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I had the problem before and had to call in a Tech to repair the baking element in my oven. It cost me $150.00 for the repair. This time I decided to do the repair myself, so I went online and found this site The instruction video made it very easy. I am very proud of what I was able to do without calling a Tech. My oven works like new, I t only cost less than $40.00 for the total repair. I am so glad this site were there when I needed them.. Thanks a Lot..
Was this helpful?
Thank you for voting!
All Instructions for the 3822
61 - 75 of 405