36361 - Instructions

once the part arrived, it was a perfect fit and just snapped on! DONE!

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the ... Read more Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen

UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn ... Read more 't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.

The video on the site is easy to understand and a snap to follow.

I visually inspected the compressor and narrowed down the source of the noise to the freezer area. Then I removed the doors and the screws securing the divider panel. Next I removed the bottom panel of the freezer, the styrofoam insullation panel and the evaporator motor. The motor is mounted between two grommets. I replaced the gromme ... Read more t facing the fan blades. The aluminum reflector below the styrofoam insulation panel had also come loose. I reattached it and reassembled the refrigerator in reverse order. The noise is gone!

Purchased spanner wrench for tub nut wouldn’t budge, impacted off. Then spin tub took 2days to get loose, lots of WD40 , also heated up center area, used a small sledgehammer head to hit a socket on the large part of the shaft . Had to take out outer tub to replace seal and support bearing unit.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

First, I removed the 2 screws for the top panel, lifted the top panel off, then I removed the 2 screws holding the front panel, tilted it forward to clear the drum, disconnected the door switch and set the panel aside. I then installed the 4 slides on the new front bearing, removed the light socket from the old bearing, removed and disca ... Read more rded the old bearing. I installed the light socket into the new bearing and the bearing assembly snapped into place on the front panel. I then re-connected the door switch, aligned the front panel with the drum, secured the front panel with 2 screws, then carefully placed the top panel back in place and secured it with 2 screws. I checked the rotation of the drum and it worked like a champ. Matter of fact, that same day I put this dryer and a matching washer up for sale at 8:30 am on October 31st and by 9:20 am I already sold them!! I delivered and hooked them up and the dryer works great!!!

If you're handy with a right angle grinder and a cutoff wheel, it can be done.

Order the washer hub, hub nut, and the spring washer above the hub nut.

Get the agitator out. a pair of flat bars and some hammering on the agitator retaining bolt helps a lot. Loosen the retaining nut a few turns, pry and hammer at the s ... Read more ame time, repeat until he agitator comes out.

On the bottom of the tub assembly is a brown plastic bracket that holds the spin solenoid. Remove it before you dismount the tub assembly. It's easy to break, and it costs $65.

Dismount the tub assembly from the cabinet. Turn it over and remove the motor. Unbolt everything that can be unbolted. Cut away enough of the large metal plate that was bolted to the bottom of the tub so that the tub assembly will stand upright on a five gallon bucket.

Stand the tub assembly upright on the five gallon bucket. Cut away the hub nut. Try not to cut into the black steel disk on the bottom of the tub. Soak the metal parts with PB Blaster, Kroil, or similar. Slip a three foot long piece of 1 1/4 pipe or conduit over the stem that held the agitator. Hold the pipe upright. Drop a four foot long steel rod into the pipe. Use the steel rod as a slide hammer and whale away. Stop frequently to spray your penetrant, and keep hammering. Eventually you'll drive the old washer hub out of the drum. Remember, everything is plastic and not indestructible..

Before reassembly turn the tub over and clean up the mating surfaces, ditto the agitator. When reassembling use antisieze compound on the mating surfaces.

I've experienced same symptoms on previous dryers over the last 30+ years, so I immediately ordered a rear drum bearing replacement kit from PartSelect. Perfect replacement parts for replacement of OEM parts.

1) After unplugging dryer, moved it to garage because of expected dust and lint deposits.
2) Removing two screws un ... Read more der from top lip allows top to lift and rotate off of dryer.
3) Removing two screws inside on both sides allows the front panel to be removed. Just remember to lift drum when you pull pannel off.
4) Best to take front panel off completely, so remove single screw on green ground wire at lower left and disconnect the white two wire connector (pull apart). Three wires need to come off of door switch (yellow/brown and white leading from the dryer inerds and one white to the drum light). Best to tag or remember where they connect. Otherwise, white from inerds goes to switch common, y/b goes to normally open and bulb white goes to normally closed terminals.
5) Get someone with really skinny arms to reach in to slide drum belt off of idler pulley. Otherwise, long sleeves are a necessity to keep from getting sliced to pieces on sheet metal edges.
6) Lift drum out and away from dryer frame. It's a pretty tight fit so get a helper to spread the side panels apart a bit.
7) Replace both bearing pin in drum and bearing socket in heater pan, following instructions that come with the parts or the video that is on the PartSelect website.

Didn't expect the drum slides and top drum slide support to be worn out, so I had to order them ASAP from PartSelect. The slides were totally gone and the support assemble was effectively toast. You might seriously consider replacing the slides and the lower felt when you try to fix the squeeks, since they are a major source of the noise and take an additional 2-3 minutes to replace.
8) Reassembly of the dryer is just doing the above steps in reverse. Best to clean out as much lint/dust as possible, since a clean dryer is an efficient dryer and we all want to make our "green" friends happy nowadays.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

I removed the washer front cover and slanted cover between washer and drier to see where the noise was coming from. I found 2 rubber stabilizing straps broken away from the tub cap and popped off the snap on tub cap to see if I could repair it. I could not, so, I ordered a new tub drip cap thinking that would solve the problem. Well, the ... Read more new cap was not identical to the one I took out. The pegs that the straps are supposed to connect to were nonexistent ... frustrating. After reading several help files, I discovered that GE had changed the design of the drip cap intentionally and had done away with the stabilizing straps. There was no mention of the design change in the instructions that came with the new part. Okay, now the real fun began...LOL. Removing those darned tub hangers was a challenge because I was working alone and in a very confined area. The instructions said to remove the 2 front hangers and let the tub sit on the floor. I did not like doing that for fear of damaging other parts under the tub. Additionally, I could not reach the rear hangers if I did it the recommended way. So, I used some oak boards and straps to lift (jack up) the tub as high as possible and to remove the weight off of the tub hangers. With the weight removed from the hangers, they snapped out of place...not easily. The 2 rear hangers are hard to reach and the plastic hanger caps were difficult to unsnap. I had to slam the plastic caps against the frame to get them unsnapped from the metal rods. The instructions did not contain any description of how the hangers are connected or how to get them removed. Anyway, I put it all back together and tested it. Everything is working fine now...minus the stabilizing straps. It would be very easy to injure yourself doing this job. Take your time and consider the consequences before jumping into this alone or with improper lifting equipment or mechanical skills. It was tedious and frustrating but not impossible. Good luck!