36361 - Instructions

First I called to get help with the right part and they told me I needed the pus-to-start-switch. It came in and I called my handyman Ed to install it. I am happy with your service. I dont install but just got the part in.

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapp ... Read more ed the new switch into place.

10 minutes total.

snapped in new latch

Open the dryer door and remove the two screws in the top of the door opening that hold the top of the dryer on, and then remove the dryer top. On the inside of the dryer, there are two screws that hold the front of the dryer on. Remove one screw from each side of the dryer near the top, and the front of the dryer will fall away. The d ... Read more rum slides are visible when you lean the front panel of the dryer out away from the drum. You can replace the drum slides without even removing the front of the dryer completely. Pull out the old drum slides and insert the new slides. Lift the drum slighly from the inside through the dryer door as you tilt the front back into place. Reinsert the screws holding the front of the dryer on and tighten. BE CAREFUL not to drop the screws or you may have to disassemble the dryer to get at the dropped screws. Reinstall the top of the dryer. It is a difficult fit which requres inserting into 3 tabs and sliding the top into place. Check that the top is flush before inserting and tightening the screws in the top of the door opening.

watched the video on your website,this made repair to the dryer very easy.hardest step in the repair was getting the belt hooked up on motor and tensioner,but being old and persistent i finally won!

watched the video, and it was simple!

My dryer knob broke on the timer cycle switch so I ordered a new one along with a new dryer knob which didn't fix the problem, then I ordered the start switch and all I had to do was remove the back of the dryer where all the knobs are located and remove the start switch by turning the start switch to remove it, replace it with the new o ... Read more ne by turning it till it clicks in just like when you removed it, put knob back on the front. However that didn't fix my dryer either so I ordered the thermal fuse and switched it out and that was what started the dryer back up. It is located on the back all the way to the bottom where the electrical cord is. Remove the cover and locate the fuse. Use a pair of pliers to pop it out and push the new one back in.

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtub ... Read more e videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove ... Read more the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

I went to You tube sight to see how I can remove front of washer so I could inspect inside and see if the problem was visible. A butter knife easily released the tabs that hold the front of washer on. My wife in the mean time found a you tube video that showed the same problem and I ordered the part right away. It showed just two screws a ... Read more nd a plug that had to be removed. I always buy my parts from part-select because the quality and speedy delivery and tracking is great! This was an easy fix!

Came home one evening and found the refer compartment evaporator fan making a noisy/grinding noise. While waiting for the part to arrive the motor finally quit working and the frige lost its ability to cool, but the freezer still worked fine. This is the fan that is inside the frige between the refer & freezer compartments - NOT the fan m ... Read more otor that is located in the bottom/rear next to the compressor. This grinding noise sounded like it was coming from inside the frige and could be easily heard under the vegetable trays and above the freezer compartment. To access this motor you need to go after it from inside the bottom of the frige compartment - there's NO need to remove the refer door. Pull the vegetable trays and remove the small phillips head screw located down in the lower air flow groove toward the front of the refer. Next, pry up & out the front white trim piece that runs the width of the frige. Once that piece is removed you can lift & slide back the whole lower frige trim/tray. Now lift out the large foam block compartment and you'll have complete access to the evaporator fan motor and the evap coils. Simply pull the fan motor assy out, still attached to the triangular bracket and disconnect the electrical pigtail. Next, pull the fan blade straight off the front hub, split & disassemble the motor bracket, & replace both fan motor grommets. Reverse the steps to reassemble the fan motor to the bracket and reinstall back in the bottom of the frige and plug in the electrical pigtail - the fan should (quietly) fire off instantly and begin the cooilng process. Reinstall the foam block, lower frige tray, front trim piece, reattach the phillips screw, close the door, and give it some time - it took our frige overnight to completely cool down. This is not a tough job, I spent more time figuring out how to access the motor then the actuall replacement. Hope these steps help to speed up your repair! And remeber Red Sox 4 Life!

Replacement handle easily snapped into dryer door. No skill or tool needed,.

Ordered lid switch from parts select via website. Two days later I received the part in the mail. Instead or re-wiring, I cut wire close to existing bad switch. Splice two wires and cap with wire nuts. Zip tie loose wire to tub housing.