My Orders
362756 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Part rusted over time...22 years.
2 of 2 people
found this instruction helpful.
-
Jeannene from HUNTINGTON, TX
- Very Easy
- Less than 15 mins
-
Screw drivers
Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.
Was this helpful?
Thank you for voting!
Drawer support broke
2 of 2 people
found this instruction helpful.
-
Charles from BOULDER, WY
- Really Easy
- Less than 15 mins
-
Nutdriver
Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plas
... Read more
tic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.
Read less
Was this helpful?
Thank you for voting!
Bottom part of the Drawer Glider broke off on both sides of the drawer.
2 of 2 people
found this instruction helpful.
-
William from SPOKANE, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove the draw from the stove. Then unscrew two Phillips Head screws ( one on each side). Remove the old gliders. Slip in the new gliders. Screw the two phillis head screws back in. Make sure when you put the drawer back in the stove that you lift the front of the drawer up enough that the lower portion of the new glider is engaged on t
... Read more
he side rail of the oven drawer space.
Read less
Was this helpful?
Thank you for voting!
Part will wear out after a couple of years
2 of 2 people
found this instruction helpful.
-
Richard from Mt Solon, VA
- Easy
- Less than 15 mins
-
Nutdriver
In my case it was the lower burner so I unplugged oven and turned gas off.
Then I removed the bottom drawer, and the lower burner cover.
Next unplug Oven Igniter, found where drawer existed.
Removed 2 screws attaching Igniter using nutdriver
Placed new Igniter on
Plug Igniter in and tested oven
Replace burn ... Read more er cover and drawer
This was much easier then what I went through with a repair man the first time around. These Igniter are designed for certain model stoves and are not interchangable with other model stoves!!!
Then I removed the bottom drawer, and the lower burner cover.
Next unplug Oven Igniter, found where drawer existed.
Removed 2 screws attaching Igniter using nutdriver
Placed new Igniter on
Plug Igniter in and tested oven
Replace burn ... Read more er cover and drawer
This was much easier then what I went through with a repair man the first time around. These Igniter are designed for certain model stoves and are not interchangable with other model stoves!!!
Read less
Was this helpful?
Thank you for voting!
GOT 1-SMALL 2-MEDIUM 0-LARGE CAPS
2 of 2 people
found this instruction helpful.
-
Teddy from Bel Air, MD
- Difficult
- Less than 15 mins
PLEASE BE ADVISED WHEN THEY SHIPPED THE BACK ORDER 1 -(taupe) LARGE CAP - RECEIVED 4 BLACK CAPS - 1-SMALL
2-MEDIUM 1-LARGE (ALL BLACK) - STILL LOOKING FOR
A LARGE CAP IN taupe color!
Received refund for 1-large cap
PROBLEM IS ALL OTHER PARTS ON THE GAS STOVE
ARE taupe in color - do not want black!
... Read more r />your advice?
2-MEDIUM 1-LARGE (ALL BLACK) - STILL LOOKING FOR
A LARGE CAP IN taupe color!
Received refund for 1-large cap
PROBLEM IS ALL OTHER PARTS ON THE GAS STOVE
ARE taupe in color - do not want black!
... Read more r />your advice?
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Drawer sticking and not operating smoothly
3 of 5 people
found this instruction helpful.
-
Bill from Philadelphia, PA
- Easy
- Less than 15 mins
-
Screw drivers
I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.
Was this helpful?
Thank you for voting!
Burner had uneven flames
3 of 5 people
found this instruction helpful.
-
Akshay from Bridgeton, NJ
- Really Easy
- Less than 15 mins
Too easy a five year old could do it
Was this helpful?
Thank you for voting!
Broken drawer glider
2 of 2 people
found this instruction helpful.
-
James from RANCHO MIRAGE, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
Was this helpful?
Thank you for voting!
No problem
2 of 2 people
found this instruction helpful.
-
Laurindalva from LODI, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver
I used a nutdriver to remove the natural gas orifice and I placed the other liquid gas orifice
Was this helpful?
Thank you for voting!
rusted trim strip
3 of 5 people
found this instruction helpful.
-
Larry from Sarasota, FL
- Really Easy
- 15 - 30 mins
-
Socket set
remove screws, re-install screws
Was this helpful?
Thank you for voting!
The trim piece on the bottom of the door was rusted making the unit look really dirty and used.
2 of 2 people
found this instruction helpful.
-
Glenn from West Melbourne, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove
... Read more
looks like it's brand new.
Read less
Was this helpful?
Thank you for voting!
Gas Broiler Igniter didn't work. Broiler would not come on
2 of 2 people
found this instruction helpful.
-
James from Guilford, CT
- Easy
- 15 - 30 mins
-
Nutdriver
Pulled the gas stove out so that I could shut off the gas valve and unplug the power cord. Job was made easier by removing the oven door (which just slides out). I took the 2 screws out that held the old igniter in place. Went to the rear of the range where there was a small 3"X2" electrical cover for the igniter, and disconnected the
... Read more
wire leads from the wiring harness. I then pulled the old igniter out through the oven front. Fed the new igniter wires through the back of the range and plugged the new igniter in. Reinstalled the electrical cover in the back of the range, attached the 2 -1/4" screws to reinstall the igniter inside the broiler. Put back the oven door. Turned the gas valve back on and sprayed on a soapy solution to check for gas leaks. Plugged the electrical cord back in. Pushed range back in place, Turned broiler on. Wait for a few seconds till the gas comes back thru the line. Works great Our stove was a GE Profile Gas Range. The part number for the igniter is WB13K21. We are very satisfied. Jim
Read less
Was this helpful?
Thank you for voting!
Replaced igniter pins but no joy, needed igniter module
2 of 2 people
found this instruction helpful.
-
Tim from NASHVILLE, TN
- Easy
- 15 - 30 mins
-
Nutdriver
Most videos show getting to the igniter module from the front when in fact with this older GE its accessed through the back left corner from the backside. So easy, a few screws and I was in. Quick change out and all worked well again.
Was this helpful?
Thank you for voting!
Oven would not light
2 of 2 people
found this instruction helpful.
-
WAYNE from HAMMOND, NY
- Easy
- 15 - 30 mins
-
Nutdriver
Tested for power to the igniter, (had power) so I knew it must have been the igniter that had failed. Removed two screws that held the shield in place, remove two screws that hold the igniter and disconnect the plug form the igniter, replace with new igniter.
Was this helpful?
Thank you for voting!
Igniter was glowing but would not light the oven.
2 of 2 people
found this instruction helpful.
-
Gary from ROCKY POINT, NC
- Easy
- 15 - 30 mins
-
Nutdriver
Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.
Was this helpful?
Thank you for voting!