3621 - Instructions

Followed instructions per video and took roughly 45mins. Super easy and saved you time from having to hire someone and money. Highly recommend do it yourself.

removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.

First turned off power and removed top shelf.
Then I used a flathead to slowly pry the switch out by the two sides. You just anlge ita bit and it slideds out easily. Then I disconnected the wires from the old switch, connected the new one and installed the new switch by snapping it back into the cutout.

Pulled out the control sensor on the ceiling of the fridge. (2 screws) Took a picture with phone on how everything was installed. Unplugged all wires and pulled out Control Temp sensor. Installed new one and attached all wires. Installed back in fridge and plugged it back in. Everything works like new.

First I removed the 4 screws in the back of the freezer. I then pulled the connection from the fan , I replaced the fan to the connection, replaced the 4 screws and I was done! I still can't believe how simple it was.

Look were timer was located, in my refigerator is next to the dial to ajust the temperature. used a screwdriver to get panel off. replaced timer then used a straight screwdriver to advance timer to turn on compessor . monitor temperature . checked out.

Turned off the power at the breaker box. Removed the two screws, pulled the element out about 3 inches, disconnected the two wires, reconnected the two wires to the new element, inserted element back into place, screwed in the screws...all finished...works great! Delivery was super fast...just a great experience all the way around.

No instructions came with new parts. Access to element was impossible until I accidentally discovered that the two styrofoam cushions at the ends of the coils were removable. Once removed, access to the heater and thermostat was very easy.

Unplug appliance, remove freezer shelf, cold air ducts, back of freezer, disconnect lig ... Read more ht, (My model does not have ice maker. This may also need to be disconnected.)
1.Remove styrofoam cushions at end of coils
2.Locate element between bottom two coils
3.Disconnect the male/female connections
4.Remove support clip under center of element
5.Remove element
6.Replace new element in reverse

Connecting the thermostat wires was challenging because they were somewhat behind the coils.

1.With styrofoam removed, unclip thermostat from coil
2.Carefully cut wires (leave enough to connect new wires)
3.Connect new thermostat wires (color of wires matched on my fridge)
4.Clip new thermostat in place
5.Replace styrofoam
6.Button it all up

With these steps, this job would take maybe 30 minutes; somewhat longer if your model has an icemaker.

Hope this helps.

Removed old worn out freezer fan motor and replaced with a new one. Piece of cake. Sooo easy and saved money too!

pulled out switchs verified part #'s-ordered replacements- its actually plug in switches and very simple

The Crisper Glass Shelf Broke. My son removed it to clean and dropped the shelf. I ordered a replacement shelf which arrived in record time and just slid it into place.

Simply removed the screws and pulled the old handle off and aligned the new handle with the holes and replaced the two screws.

Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.

Being a woman, I first cleaned the oven. Removed two screws holding the element in place. Pulled element out about 3 inches and disconnected one clip attached to a yellow wire another clip attached to a green wire. Put new element in connected clips. Replaced screws.

I took the broken part off the bar, put the new part on the bar, snapped it into the fridge, threw the old part out, opened the fridge admired my work, while I was ther I grabbed a beer....couldnt have gone better.