3527 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
didn't eject icecubes
9 of 12 people
found this instruction helpful.
-
Ronald from Marion, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver
R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin
Very Satisfied,
Ron Martin
Was this helpful?
Thank you for voting!
No cooling, compressor not running and was very hot
8 of 9 people
found this instruction helpful.
-
Miriam from Canyon Country, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Plied off the relay switch with a screw driver. I could not pull it off by hand. Disconnected the wires to it and replaced with new part. Had problem getting the part back on and lining up the pins with the connector. I had to line up one pin and start at an angle and roll the part onto the contact pins.
I was impressed with the one ... Read more day delivery without paying because it was shipped from a warehouse in California where the repair was made.
I was impressed with the one ... Read more day delivery without paying because it was shipped from a warehouse in California where the repair was made.
Read less
Was this helpful?
Thank you for voting!
Fridge random humming
9 of 12 people
found this instruction helpful.
-
robert from central point, OR
- Really Easy
- 15 - 30 mins
-
Nutdriver
Unscrewed back of fridge and unplugged relay from compressor and plugged in the new one remember that the new one turns 180 degrees from existing switch.
Was this helpful?
Thank you for voting!
The oven wouldn't heat
8 of 9 people
found this instruction helpful.
-
Richard from Wilmington, MA
- Really Easy
- Less than 15 mins
-
Pliers
First I shut off the power at the circuit breaker.Then I removed the racks to make room to work.I then removed the 2 screws holding the element in place and pulled both sides out approx.3 inches.After carefully disconnecting the wires,I put the new element in to place and repeated the steps backwards.
Was this helpful?
Thank you for voting!
replacing thermostat did not help
10 of 15 people
found this instruction helpful.
-
John from Rocky River, OH
- Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set
Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiv
... Read more
er boaed. I turn off manually the icemaker, when needed
Read less
Was this helpful?
Thank you for voting!
Replaced door cam closer
7 of 7 people
found this instruction helpful.
-
Ronald from Cumming, GA
- Easy
- 15 - 30 mins
-
Nutdriver
Replaced the part--
Door snaps loudly everytime it's opened or closed.
Correct replacement part and lubed with vaseline,
Door snaps loudly everytime it's opened or closed.
Correct replacement part and lubed with vaseline,
Was this helpful?
Thank you for voting!
Power surge cause compressor to stop functioning
7 of 7 people
found this instruction helpful.
-
Alvin from ORANGE PARK, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Followed the YouTube video linked to the Compressor Start Device and Capacitor I purchased. The repair was just as easy as the technician in the video said it would be. Removed the back panel, remove the clamp, worked the Compressor Start Device and Capacitor off the electrical prongs and replace it with the new one. After I reassemble
... Read more
the refrigerator, it was fully operational. Very easy to do and only required a few tools.
Read less
Was this helpful?
Thank you for voting!
Front left burner quit after bright flash under glass top
11 of 19 people
found this instruction helpful.
-
Brian L. from Wilkes-Barre, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
I ohmed out the burner element that wasnt working and found it was open. I ordered a new element thru PartSelect and installed it in the stove. I powered up the stove and turned on the burner but it didnt get hot. After a bit of testing I found that the new elements safety overtemp terminals werent in the same configuration as the origina
... Read more
l unit. I made some wiring adjustments and the burner was operating properly. Thanks PartSelect
Read less
Was this helpful?
Thank you for voting!
The Freezer defrosted and everything on the top and the bottom spoiled
10 of 16 people
found this instruction helpful.
-
Jorge from Miami, FL
- Easy
- 15 - 30 mins
-
Nutdriver
i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burn
... Read more
ed. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.
Read less
Was this helpful?
Thank you for voting!
Burner would only cook on high setting or not heat up at all.
9 of 13 people
found this instruction helpful.
-
Judy from West Salem, IL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power
... Read more
and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.
Read less
Was this helpful?
Thank you for voting!
Freezer not getting cold enough to freeze ice cream
8 of 10 people
found this instruction helpful.
-
Gary from ROSETO, PA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Read less
Was this helpful?
Thank you for voting!
broken ice bucket
7 of 7 people
found this instruction helpful.
-
kevin from yucaipa, CA
- Easy
- Less than 15 mins
-
Nutdriver
Removed Ice bucket. Removed two screws and removed front cover from old ice bucket, two more screws under cover to remove ice agitator. Installed ice agitator to new ice bucket, installed two screws holding it. Installed ice bucket front cover on new ice bucket with two screws. Put new ice bucket into freezer. Finished! That was easy!
Was this helpful?
Thank you for voting!
Water kept running out of water dispenser
8 of 10 people
found this instruction helpful.
-
Richard from Austin, TX
- Really Easy
- Less than 15 mins
-
Wrench set
Repair man wanted $240.00 to fix this problem. I simply removed panel from bottom of back of refrigerator and disconnected two screws and the water and the part was free reconnected water and the two screws and done deal with a $40.00 part.
Was this helpful?
Thank you for voting!
Compressor would not start
7 of 7 people
found this instruction helpful.
-
Rich from Monon, IN
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed back access cover with quarter inch nut driver, unplugged wire harness, pulled old relay out & plugged in new one, reconnected wire harness, and reinstalled access cover. Piece of cake. (Shipping was very quick) ***Frig was only 3yr an 1 mounth old.*** Maytag - Dependable Huh?
Was this helpful?
Thank you for voting!
My ice maker stopped working and just leaked water endlessly
9 of 13 people
found this instruction helpful.
-
Patricia from Sebastopol, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I ordered the ice maker, but not the wiring harness...didn't fix the problem so I ordered a wiring harness, but ordered the wrong one...so I emailed parts select and got a prompt response on how to return the mistake and which part I actually needed. It was a "special order" but got in within days. Wonderful service!
Was this helpful?
Thank you for voting!