3527 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Globs of Ice around ice maker and bucket
71 of 77 people
found this instruction helpful.
-
Rudolph from Redondo Beach, CA
- Easy
- More than 2 hours
-
Nutdriver, Pliers
I originally ordered the part because of globs of ice being around the icemaker. The icemaker then quit making ice altogether after a few weeks of removing the ice globs (so the spindle of the icemaker would rotate again). It came to me that there was now no water being supplied to the icemaker hence, "no ice". Decided to replace the w
... Read more
ater valve as the most likely culprit.
Removed the bottom back panel behind the refrigerator. Turned off water supply. Unplugged refrigerator power plug. Unscrewed the hose connection to the valve and two small plastic feeder tubes going to icemaker and ice water dispenser in the front door. Removed spring clip securing the valve to its mounting flange. Pryed up the valve out of its mounting flange as it is mechanically held there by a pressure fit. Maneuvered the valve out and into my hand. Removed the two electrical connectors and draped them to the side. Reversed the entire procedure with the new exact replacment valve.
Unfortunately, stlll no water was being supplied to the ice maker. Water to the dispenser in the door was still fine. I reasoned that the icemaker, not receiving any water from the fill valve, must be because the signal from the sensor (where ever that was located), must not be getting to the fill valve to tell it to open up and send water. Then a light bulb went off in my head. Where would that sensor be? Epiphany......How about the icemaker itself? Ordered the icemaker, replaced it and I now have ice again. Replacing the icemaker was a tougher job but that's another show. I'll report on that process under a separate repair story under the icemaker category.
The replacement of the valve took only about two hours, mostly because I had to round up my drill, attach a nut driver accessory, move the refrigerator and vacuum out all the gunk and fuzzy stuff from behind the refrigerator (yuck). Actual valve replacement only took about 1/2 an hour what with having to remove a put back a dozen or so machine screws on the back panel.
Removed the bottom back panel behind the refrigerator. Turned off water supply. Unplugged refrigerator power plug. Unscrewed the hose connection to the valve and two small plastic feeder tubes going to icemaker and ice water dispenser in the front door. Removed spring clip securing the valve to its mounting flange. Pryed up the valve out of its mounting flange as it is mechanically held there by a pressure fit. Maneuvered the valve out and into my hand. Removed the two electrical connectors and draped them to the side. Reversed the entire procedure with the new exact replacment valve.
Unfortunately, stlll no water was being supplied to the ice maker. Water to the dispenser in the door was still fine. I reasoned that the icemaker, not receiving any water from the fill valve, must be because the signal from the sensor (where ever that was located), must not be getting to the fill valve to tell it to open up and send water. Then a light bulb went off in my head. Where would that sensor be? Epiphany......How about the icemaker itself? Ordered the icemaker, replaced it and I now have ice again. Replacing the icemaker was a tougher job but that's another show. I'll report on that process under a separate repair story under the icemaker category.
The replacement of the valve took only about two hours, mostly because I had to round up my drill, attach a nut driver accessory, move the refrigerator and vacuum out all the gunk and fuzzy stuff from behind the refrigerator (yuck). Actual valve replacement only took about 1/2 an hour what with having to remove a put back a dozen or so machine screws on the back panel.
Read less
Was this helpful?
Thank you for voting!
No ice in ice trey
79 of 104 people
found this instruction helpful.
-
Wayne from Leesburg, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace h
... Read more
olding pins and start the process of putting back together the opposite way you took it apart.
Read less
Was this helpful?
Thank you for voting!
Frig not cold at all,Freezer was all defrosted
65 of 71 people
found this instruction helpful.
-
Denise from SOUTHINGTON, CT
- Easy
- 15 - 30 mins
-
Pliers
Well the frist thing I did was get out the all the paper work and look under trouble shooting.This frig has a list of codes to try to help narrow down what parts might be bad.Well at frist it seemed it was a Defrost Thermastat?Well thanks to PartSelect it showed me right where it was and step by step how to remove and replace it.It took m
... Read more
e over 2Hr's,after that I let the frig run all night and the next morning(yep warm frig)not the part I needed,well now Im mad,the local part store said you need a 3in1 jump starter easy to in stall at $50.Can'nt bring parts back no way weather thier opened or not.So get home and can'nt see how this jumper is going to wire up to my compresser?So on to the Web site to get some info,find out that this part gets a thumb's down,it puts out more volt's then needed and kills your compresser the reviews where very help full.So back to PartSelect to see more info,then I spoted the Overload/Relay and went to the back of my Frig and this part just plugs right into the compresser,I pulled it of with pliers and Bingo a burn spot melted right through the Overload/Relay.Ordered the right part the same as the old one.Put the part in and Bam,compresser fired right up.If I only did alittle more home work I could off saved alot of head ach and money.Thanks PartSelect I'll alway's click on to your web site for future parts and advise.
Read less
Was this helpful?
Thank you for voting!
The original heating element shorted and caught fire
89 of 151 people
found this instruction helpful.
-
Eric from Tooele, UT
- Really Easy
- Less than 15 mins
-
Screw drivers
The repair was simple; I removed just two screws, pulled out the wires, and slipped the two spade connectors off the original element. The repair was simply the reverse of the disassembly. The only thing to remember is to throw the circuit breaker before handling the electrical connectors. Other than that, it couldn't be any more strai
... Read more
ght forward.
Read less
Was this helpful?
Thank you for voting!
getting "black plastic" pieces on ice
53 of 60 people
found this instruction helpful.
-
Kathy D from Waterford, MI
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I didn't know what the plastic was - just that it was unappetizing. Reading other posts, it must have been the teflon coating. The refrigerator is 13 years old and reading other posts, I guess I'm lucky it lasted that long.
My boyfriend did the repair and here is his story:
The first ice maker we received was cr ... Read more acked on one corner. Not knowing how it got that way, I was concerned that there might be additional internal damage and that the unit wouldn’t work properly. Part Select was contacted and a replacement unit was sent with no difficulty.
As other reviewers have said, the replacement was quite easy, taking less than half an hour. The only tools I needed were a screwdriver and a nut driver. To begin, unplug the refrigerator and turn off the water supply to the ice maker. Loosen, but do not remove, the two top attachment screws. Then remove the bottom screw. Lift the unit up off the top screws and remove the water inlet hose at the top right. It’s probably a good idea to have a container handy to catch the small amount of water that comes out, but you’ll need a third hand for this.
The electrical wiring harness is very short and may be tricky to disconnect. On my refrigerator there is a round vinyl connector that plugs into a receptacle on the back wall of the freezer compartment directly behind the ice maker. This was removed with no difficulty (accidently, actually). Once the unit is out of the refrigerator you can remove the connector from the ice maker by using a screwdriver to depress the latch tab that is visible in a window in the unit housing. When installing the connector in the new unit make sure it is fully seated. Next, reconnect the round vinyl connector to the receptacle on the back wall of the freezer compartment. This was the worst part of the whole procedure. You have to support the unit close to the back of the freezer (due to the short harness) with one hand while inserting the connector with the other. This requires both arms in a confined space. The first time I did it I apparently didn’t get a good electrical connection on one end of the harness, and it didn’t work. Because the connectors are directly behind the ice maker I had to remove the unit and re-install it, but it was much quicker the second time, less than 10 minutes.
Once the connectors are in place put the water inlet hose into the opening at the top right. You may need to re-use the retaining clip from the old unit for this. Slide the two top mounting ears down between the screw heads and the back wall of the freezer compartment and tighten the screws. Then install the bottom screw. Plug in the refrigerator, turn on the water and make yourself a frosty beverage.
All in all, a relatively quick and painless procedure.
Another note - we kept saying "is there ice yet"? I think the metal bar that controls the ice maker needed to be raised and lowered a few times before it would work properly as it seemed to raise 1/2 way but the ice would not drop so I put it down and it worked its way up. Had to do it a couple of times over a 4 hour span but once going, it is working like a champ.
My boyfriend did the repair and here is his story:
The first ice maker we received was cr ... Read more acked on one corner. Not knowing how it got that way, I was concerned that there might be additional internal damage and that the unit wouldn’t work properly. Part Select was contacted and a replacement unit was sent with no difficulty.
As other reviewers have said, the replacement was quite easy, taking less than half an hour. The only tools I needed were a screwdriver and a nut driver. To begin, unplug the refrigerator and turn off the water supply to the ice maker. Loosen, but do not remove, the two top attachment screws. Then remove the bottom screw. Lift the unit up off the top screws and remove the water inlet hose at the top right. It’s probably a good idea to have a container handy to catch the small amount of water that comes out, but you’ll need a third hand for this.
The electrical wiring harness is very short and may be tricky to disconnect. On my refrigerator there is a round vinyl connector that plugs into a receptacle on the back wall of the freezer compartment directly behind the ice maker. This was removed with no difficulty (accidently, actually). Once the unit is out of the refrigerator you can remove the connector from the ice maker by using a screwdriver to depress the latch tab that is visible in a window in the unit housing. When installing the connector in the new unit make sure it is fully seated. Next, reconnect the round vinyl connector to the receptacle on the back wall of the freezer compartment. This was the worst part of the whole procedure. You have to support the unit close to the back of the freezer (due to the short harness) with one hand while inserting the connector with the other. This requires both arms in a confined space. The first time I did it I apparently didn’t get a good electrical connection on one end of the harness, and it didn’t work. Because the connectors are directly behind the ice maker I had to remove the unit and re-install it, but it was much quicker the second time, less than 10 minutes.
Once the connectors are in place put the water inlet hose into the opening at the top right. You may need to re-use the retaining clip from the old unit for this. Slide the two top mounting ears down between the screw heads and the back wall of the freezer compartment and tighten the screws. Then install the bottom screw. Plug in the refrigerator, turn on the water and make yourself a frosty beverage.
All in all, a relatively quick and painless procedure.
Another note - we kept saying "is there ice yet"? I think the metal bar that controls the ice maker needed to be raised and lowered a few times before it would work properly as it seemed to raise 1/2 way but the ice would not drop so I put it down and it worked its way up. Had to do it a couple of times over a 4 hour span but once going, it is working like a champ.
Read less
Was this helpful?
Thank you for voting!
The door was crocked and wouldn't shut properly
46 of 53 people
found this instruction helpful.
-
Arau from Haverhill, MA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Everything was easy. I read one of your other reviews and it gave me the confidence to try it myself. First i toke off the cap at the top of the door then the three screws. I lifted the door off so i could be sure the cam was my only problem then put the door back on. That took 5 mins. Then I got on the computer and ordered the parts i ne
... Read more
eded. Two days later the parts arrived and and i took the door off again. Then put the new cam on, applied a litle vasiline, put the door back on and forgot that i ever had a problem. Thanks for the help. Doug Arau
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
ice maker did not make ice
49 of 64 people
found this instruction helpful.
-
DAVID from TINLEY PARK, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting po
... Read more
wer in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.
Read less
Was this helpful?
Thank you for voting!
Icemaker was dumping water into ice bin and the ice maker shut off arm broke its rear mount
51 of 72 people
found this instruction helpful.
-
GORDON from CUPERTINO, CA
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
First I removed the 14.3 tons of freezer contents, closed the water valve, shut off the juice, and removed the freezer bins, the freezer door and the three screws that held the element in place. After bringing in 397 hand tools from my garage inventory, I loosened the unit and, after extensive evaluation, I finally disconnected the wiring
... Read more
connector from its freezer rear wall connector counterpart. You ain't gonna believe the rest of my story--of total ineptitude by an experienced fix-it-yourself dummy.
I searched the internet for a replacement ice maker and found it at partselect.com. I called Sears to ask if I could add my refrigerator to my existing appliance repair account. Sears said sure--it would cost me only one arm, three toes and one grandchild. I abruptly declined their magnanimous offer—I don’t give up my arms and toes so easily.
I visited the local Maytag repair parts and service retailer, who advised they didn't do parts anymore. Expecting their repair price would be greater than Sears, I resorted to partselect.com. I called them to be assured what I was buying was not mistakenly a 747 Landing Gear. On the afternoon (West Coast) of 4/28/10, I ordered (via internet) one PS21215123 Ice Maker Assy. Much to my pleasant surprise, it arrived via FedEX on 4/30/10 (no freight charges to me).
My repair/replacement efforts were hampered by the effects of my right rotator cuff surgery a few months before and major left wrist surgery two months ago to remove fractured bones and torn ligaments.
Undaunted by my physical handicaps, I forged forward. After re-installing the unit, I turned the water supply and electricity back on. It was graveyard dead. I wisely then bought two bags of ice as an interim solution to the severe needs of my wife and me for our daily chilled evening cocktails. I removed the unit, checked it out and re-installed it. I bought two more bags of ice. All the while, I turned the water and electricity off and on as required by reasonable safety standards. High tediousness!
Several more home maintenance tasks then arose for Sergeant Super Fixer, but I returned to the ice maker problem on 4/8/10. Last chance--remove the device and insure there was no frozen ice in the inlet tube--or call the local partsless repairman. No ice found, but I did learn the wiring connector to the unit was awry--no contact! While explaining that to my wife, I realized the two upper mounting screws were intended to be partially installed into the freezer wall to accommodate the unit's slotted mounting holes! Then, tighten the screws. Oh my God! During my 143 installations and removals, I had installed those screws blindly--using the (handicapped) skills of my right and left hands without any benefit of direct eyesight.
I returned to my challenging project this morning (4/9/10), fully utilizing all the expertise I had gained yesterday. Fifteen minutes of amusing effort! Turn on the juice! Turn on the water!Two hours later, ice cubes were dropping into the bin like rhinoceros bisquits in the jungle.
Hallelujah! I now am free for the next challenge!
HINT: Put a bed pillow (an old one, or your wife's) in the freezer compartment to soften the harshness of its cold metal on your back, if you use the "crawl in on your back" approach.
I searched the internet for a replacement ice maker and found it at partselect.com. I called Sears to ask if I could add my refrigerator to my existing appliance repair account. Sears said sure--it would cost me only one arm, three toes and one grandchild. I abruptly declined their magnanimous offer—I don’t give up my arms and toes so easily.
I visited the local Maytag repair parts and service retailer, who advised they didn't do parts anymore. Expecting their repair price would be greater than Sears, I resorted to partselect.com. I called them to be assured what I was buying was not mistakenly a 747 Landing Gear. On the afternoon (West Coast) of 4/28/10, I ordered (via internet) one PS21215123 Ice Maker Assy. Much to my pleasant surprise, it arrived via FedEX on 4/30/10 (no freight charges to me).
My repair/replacement efforts were hampered by the effects of my right rotator cuff surgery a few months before and major left wrist surgery two months ago to remove fractured bones and torn ligaments.
Undaunted by my physical handicaps, I forged forward. After re-installing the unit, I turned the water supply and electricity back on. It was graveyard dead. I wisely then bought two bags of ice as an interim solution to the severe needs of my wife and me for our daily chilled evening cocktails. I removed the unit, checked it out and re-installed it. I bought two more bags of ice. All the while, I turned the water and electricity off and on as required by reasonable safety standards. High tediousness!
Several more home maintenance tasks then arose for Sergeant Super Fixer, but I returned to the ice maker problem on 4/8/10. Last chance--remove the device and insure there was no frozen ice in the inlet tube--or call the local partsless repairman. No ice found, but I did learn the wiring connector to the unit was awry--no contact! While explaining that to my wife, I realized the two upper mounting screws were intended to be partially installed into the freezer wall to accommodate the unit's slotted mounting holes! Then, tighten the screws. Oh my God! During my 143 installations and removals, I had installed those screws blindly--using the (handicapped) skills of my right and left hands without any benefit of direct eyesight.
I returned to my challenging project this morning (4/9/10), fully utilizing all the expertise I had gained yesterday. Fifteen minutes of amusing effort! Turn on the juice! Turn on the water!Two hours later, ice cubes were dropping into the bin like rhinoceros bisquits in the jungle.
Hallelujah! I now am free for the next challenge!
HINT: Put a bed pillow (an old one, or your wife's) in the freezer compartment to soften the harshness of its cold metal on your back, if you use the "crawl in on your back" approach.
Read less
Was this helpful?
Thank you for voting!
compressor clicking but not turning on
45 of 55 people
found this instruction helpful.
-
brice from irving, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
I just opened up the fridge back panel accessed the old relay/capacitor, pulled it out, replaced with the new one, snapped it back into place, tested it (compressor came on), replaced the back panel and went on my way. Really, really easy repair.
Was this helpful?
Thank you for voting!
bad light socket
45 of 56 people
found this instruction helpful.
-
nancy from silsbee, TX
- Really Easy
- Less than 15 mins
unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to
... Read more
do it myself. easy easy easy
Read less
Was this helpful?
Thank you for voting!
Burned terminal block and filter board
95 of 208 people
found this instruction helpful.
-
Joseph from Decatur, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench set
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Was this helpful?
Thank you for voting!
Ice Dispenser had jammed up and become inoperative
40 of 47 people
found this instruction helpful.
-
James from Robinson, TX
- Easy
- 15 - 30 mins
-
Screw drivers
The parts discription was a bit vague and I wasn't sure exactly what I was ordering, but I received everything I needed and it works fine. The combination screw conveyor/ice crusher came in one piece. The ice cube bin is a plastic assembly that snaps apart. I used a wide blade screw driver carefully to facilitate assembly/disassembly.
... Read more
Once you have it apart the old converyor slips out and the new one slides in. Do not remove the two screws that hold the new assembly together. You need a phillips scredriver to take out two of the screws from the old assembly and put in the new one. That is, there are four screws and you need to trasfer two of them. Everything now works fine.
Read less
Was this helpful?
Thank you for voting!
Relay
42 of 54 people
found this instruction helpful.
-
John H from Austin, TX
- Really Easy
- 15 - 30 mins
Removed back panel. Opened cover to relay attached to the compressor and pulled off replacing with new relay. No problem.
Better than paying $250 for someone else to do it.
Better than paying $250 for someone else to do it.
Was this helpful?
Thank you for voting!
noisy fan motor
38 of 46 people
found this instruction helpful.
-
robert from nashotah, WI
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Socket set
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, c
... Read more
lose up, reverse panel. ( 20m). i also took time to clean grilles with small vac and damp rag, ( looks and sounds like new) bob Wi.
Read less
Was this helpful?
Thank you for voting!
Light Switch broke
48 of 78 people
found this instruction helpful.
-
James Richard from St. Cloud, MN
- Easy
- Less than 15 mins
-
Socket set
An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only
... Read more
swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.
Read less
Was this helpful?
Thank you for voting!