3512W Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner receptacle failed (stove over 30 years old)
1 person
found this instruction helpful.
-
BETH from COUNCE, TN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Was this helpful?
Thank you for voting!
lens light was broken and missing.
1 person
found this instruction helpful.
-
Allan from Rolla, MO
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Removed the cooktop using screwdriver. Pushed lens-light into cooktop hole.It was difficult to do and was where I spent most of my time. Next time I will spray bottom of lens- light with silicon so it goes in easier. I stood cooktop up on its side and inserted the red light assembly onto the lens-light. Reinstalled cooktop <
... Read more
br />and turned electrical power on.
Read less
Was this helpful?
Thank you for voting!
Bottom Element Burned out
1 person
found this instruction helpful.
-
Robert from Jacksonville, FL
- Easy
- 15 - 30 mins
-
Screw drivers
Turned off all power to range.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)
Reversed the process.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)
Reversed the process.
Was this helpful?
Thank you for voting!
Lower burner not heating:
1 person
found this instruction helpful.
-
John from Fishers, IN
- Easy
- 15 - 30 mins
-
Screw drivers
Ordered element and recieved in two days(yea). Removed back cover from unit. Removed two wire slide on wire clips. Then went inside oven cavity and removed two screws holding element intact. The element slid out. Installed element, re-installed two screws to hold element intact. Attached wire clips back on to element, re-attached back
... Read more
cover. Plugged unit back in and it worked perfectly. Eazy-peezy lemon squeezy.
John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600
John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600
Read less
Was this helpful?
Thank you for voting!
Oven quit in the middle of cooking the Christmas turkey. Fortunately we have a smaller oven on the top which finished the job. (a few hours late, but after a few cocktails and more visiting, it really worked out fine!)
1 of 2 people
found this instruction helpful.
-
Richard from Topsfield, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I was blown away by how easy it was to order and receive this replacement part. I went on the web on Christmas afternoon, Googled "Magic Chef" and found your website. Your ordering process could not be easier (including the on-line drawings and all). I selected the lowest cost shipping method "3-5 days." Wednesday evening, I got your
... Read more
e-mail with the tracker. Thursday afternoon the part arrived! Saturday, we opened the oven, took out the old unit, and put in the new. It worked fine! Thanks again!!
Read less
Was this helpful?
Thank you for voting!
Simple - needed to replace the drip pans on the stove between tenants in a rental apartment
1 of 2 people
found this instruction helpful.
-
Tama from Pacific Grove, CA
- Really Easy
- Less than 15 mins
This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.
Was this helpful?
Thank you for voting!
One of the broiler drawer support broke
1 of 2 people
found this instruction helpful.
-
Jay from Charleston, SC
- Really Easy
- Less than 15 mins
-
Screw drivers
Piece of cake. Removed the Phillips screw with screwdriver, placed new one on the slide and used old screw to screw it in place. Drawer does not lean to one side anymore.
Was this helpful?
Thank you for voting!
Old burner pan warped.burner sat at 15 degree angle.
1 of 2 people
found this instruction helpful.
-
Michael from Portland, OR
- Really Easy
- Less than 15 mins
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Was this helpful?
Thank you for voting!
Replacing bake element
1 of 2 people
found this instruction helpful.
-
Barry from Bay Village, OH
- Really Easy
- Less than 15 mins
-
Pliers, Socket set
Turned off power circuit to oven. Removed old element by unscrewing two nuts attaching unit to back of oven. Used pliers to help release electrical connections at both ends of element. Re-attached connections to new unit. Screwed nuts back into place. Turned power back on and cooked dinner. Total time for repair was less than 5 minutes.
Was this helpful?
Thank you for voting!
Baking element burned out while I was baking
1 of 2 people
found this instruction helpful.
-
Hurline from Cedar Park, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
I Unscrewed the attachment plates located at the back of the over. Pulled the element out so that I could "unhook" the prongs. Replaced the new element by clipping on the prong attachement (you will see where the electrical wires are). Screwed the plates back on and Vola! I'm baking again.
Was this helpful?
Thank you for voting!
Element had burned out
1 of 2 people
found this instruction helpful.
-
Judith from Star, ID
- Really Easy
- Less than 15 mins
Package arrived while I was working at the computer and my husband announced minutes later, "That's what I like to see". I didn't know what he was talking about until he tossed the packing list on my desk and said, "It works perfectly. Good Job!" It had only taken a minute to pop the new parts in and he already had water on for coffee.
Other Parts Used:
Was this helpful?
Thank you for voting!
drip-bowls wore out
1 of 2 people
found this instruction helpful.
-
Ronald E from Rochester, NY
- Really Easy
- Less than 15 mins
i read the installation instructions and followed them. first i made sure that each heating element was off. next i carefully removed each one (a total of 4) from it's plug and lifted the worn out drip-bowl up and replaced it with the new one. finally i pluged in (a total of 4) heating elements and turned them on to make sure them were wo
... Read more
rking and they did.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
1 of 2 people
found this instruction helpful.
-
Nicki from ELSIE, NE
- Very Easy
- Less than 15 mins
No problem Took off old ones and replaced with new.
Was this helpful?
Thank you for voting!
Drip pans needed to be replaced
1 of 2 people
found this instruction helpful.
-
Mark from ROSENBERG, TX
- Very Easy
- Less than 15 mins
1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements
Other Parts Used:
Was this helpful?
Thank you for voting!
Drip bowls very dirty and stained
1 of 2 people
found this instruction helpful.
-
john from donna, TX
- Really Easy
- Less than 15 mins
Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering proces ... Read more ses were simple and delivery was faster than I hed expected.
Thank you
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering proces ... Read more ses were simple and delivery was faster than I hed expected.
Thank you
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!