3448 Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broiler drawer front slide plastic guides broke so drawer sagged and was difficult to pull out.
3 of 3 people
found this instruction helpful.
-
DOUGLAS from MESA, AZ
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the single phillips screw that held each plastic slide guide to the stove, and replaced the part reusing the screws. Was so simple I didn't even have to swear. This was my mother-in-law's stove, and she was so happy to have it repaired she's fed me twice since.
Was this helpful?
Thank you for voting!
Oven wouldn't heat.
3 of 3 people
found this instruction helpful.
-
Thomas from La Crescenta, CA
- Easy
- Less than 15 mins
-
Nutdriver
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pus
... Read more
hed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat
3 of 3 people
found this instruction helpful.
-
Chris from Elkins, WV
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removing the drip pan and the bottom burner cover exposed the igniter, removing two screws retaining the bracket freed the old igniter. Removing the warming drawer allowed access to the control module to unplug the wiring on the ignitor. After making myself a diagram, I unplugged the wires and removed the malfunctioning igniter. Cutting
... Read more
the leads off the old igniter long enough to splice it on below the oven bottom with the enclosed wire nuts and attaching the new igniter (reusing the old insulation to protect the wire) took only minutes and reassembly was straightforward.
New igniter: $60
Repairman fee saved $150
Being able to tell my wife "See,
I told you I could fix it!" PRICELESS
New igniter: $60
Repairman fee saved $150
Being able to tell my wife "See,
I told you I could fix it!" PRICELESS
Read less
Was this helpful?
Thank you for voting!
Gas was escaping from underneath the burner head
3 of 3 people
found this instruction helpful.
-
Edward from ALEXANDRIA, VA
- Easy
- 30 - 60 mins
-
Pliers
The old burner head had corroded allowing gas to come out at the bottom. The actual replacement is just turning the head, lifting it out, transferring two wires with slip-on connectors from the old burner to the new one, and dropping the new one in place. Most of the time was spent sanding away corroded metal on the base to make a good
... Read more
fit. The information on the burner head says that the company has decided not to use a gasket under the head. I suggest that was a bad decision.
Read less
Was this helpful?
Thank you for voting!
oven very slow on heating up up to five minutes to ignite.
4 of 6 people
found this instruction helpful.
-
manny from oakland, NJ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
First removed oven racks then two screws to remove oven door, removed two screw of oven fan cover, ( need to remove fan cover to have clearance to removed bottom cover of oven) removed bottom cover of oven, then removed two screws holding oven igniter and cut wires of old igniter then spliced wire of new igniter to existing wire
... Read more
and reassemble in reverse order.
Read less
Was this helpful?
Thank you for voting!
Self tapping screws stripped out, one broke in mounting hole
3 of 3 people
found this instruction helpful.
-
Scott from FORT WORTH, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.
Was this helpful?
Thank you for voting!
Oven ignighter no longer works
3 of 3 people
found this instruction helpful.
-
Barry from PORTERVILLE, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel t
... Read more
ool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!
Barry
Barry
Read less
Was this helpful?
Thank you for voting!
Gas range and top oven does not light up
3 of 3 people
found this instruction helpful.
-
Albert from Boston, MA
- Easy
- 15 - 30 mins
-
Screw drivers
I pulled out the gas range, unplugged the unit from the outlet. Unscrewed about two panels, one is the black cardboard panel located on top, then the aluminum main panel.
Located the spark module, unscrewed the unit from resting plate. Did not change the plate, although the new unit came with a new one, but it doesn't fit. S ... Read more o I just rested the new one on the old plate.
Pulled each wire slowly out and inserted it onto the new spark module.
Screwed in all the panels back and returned the stove to its proper place.
The range now works as well as the oven, but my broiler still does not light up.
Located the spark module, unscrewed the unit from resting plate. Did not change the plate, although the new unit came with a new one, but it doesn't fit. S ... Read more o I just rested the new one on the old plate.
Pulled each wire slowly out and inserted it onto the new spark module.
Screwed in all the panels back and returned the stove to its proper place.
The range now works as well as the oven, but my broiler still does not light up.
Read less
Was this helpful?
Thank you for voting!
Oven will not light up or will take multiple try
3 of 3 people
found this instruction helpful.
-
charles from elmhurst, NY
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Disconnected the oven from the wall outlet. Removed the bottom panel of the oven to reach the parts. Reached in the thight spot (not for a big guy)to unscrew the old igniter. Installed the new one. Plug the oven back. Turn the oven on bake at 350. Oveb lighted up in 5 seconds ! Working great since then!!!
Was this helpful?
Thank you for voting!
OVEN WOULD NOT HEAT
3 of 3 people
found this instruction helpful.
-
Mary from MEADVILLE, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Was this helpful?
Thank you for voting!
The inside glass was broken on oven door.
3 of 4 people
found this instruction helpful.
-
Jacob from Cotton, MN
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I was pleased with how the job went.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how ... Read more simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how ... Read more simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
Read less
Was this helpful?
Thank you for voting!
Oven burner would periodically go out and re-light
3 of 4 people
found this instruction helpful.
-
Richard from Merrimac, MA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- ... Read more Connect the new part
- Re-attach to the bracket with new screws.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- ... Read more Connect the new part
- Re-attach to the bracket with new screws.
Read less
Was this helpful?
Thank you for voting!
I forgot to remove something I had saved in the oven, planning to remove it before using the range.
3 of 4 people
found this instruction helpful.
-
Marilyn from Clearwater, FL
- Easy
- Less than 15 mins
Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience
... Read more
with those in need of you services. Thanks. Marilyn Kasson
Read less
Was this helpful?
Thank you for voting!
burners not working well air leaking in from botton
3 of 4 people
found this instruction helpful.
-
Theodore from Haledon, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
The repair went very well lest then one minute to replace both burners
Was this helpful?
Thank you for voting!
Broiler drawer didn't track poperly
3 of 4 people
found this instruction helpful.
-
Keith from Atlanta, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).
Was this helpful?
Thank you for voting!