EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3448 Range - Instructions

All Instructions for the 3448
106 - 120 of 690

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken levelling leg
5 of 8 people found this instruction helpful.
  • Linda from Oneida, NY
  • Really Easy
  • Less than 15 mins
Took the old levelling leg out and screw the new one in.
Was this helpful?
Thank you for voting!
replacing oven racks
4 of 5 people found this instruction helpful.
  • Lawrence from Elmira, NY
  • Really Easy
  • Less than 15 mins
The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)
Was this helpful?
Thank you for voting!
The neon tube over the stove top went out
8 of 17 people found this instruction helpful.
  • Gunther from Columbia, SC
  • Really Easy
  • Less than 15 mins
Put a new one in.
Was this helpful?
Thank you for voting!
Old racks had melted plastic on them.
4 of 5 people found this instruction helpful.
  • James from PAINESVILLE, OH
  • Very Easy
  • Less than 15 mins
It was a replace racks not repair. No problem
Was this helpful?
Thank you for voting!
oven would not come to set heat
4 of 5 people found this instruction helpful.
  • Ralph from Portsmouth, NH
  • Really Easy
  • Less than 15 mins
  • Screw drivers
slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people found this instruction helpful.
  • peter from marine city, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Was this helpful?
Thank you for voting!
Just unscred the 2 screw on the Thermometer
4 of 5 people found this instruction helpful.
  • WILLIAM J from JERSEY CITY, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.
Was this helpful?
Thank you for voting!
Door gasket was hard and brittle from baked-on grease - heat leaking around door
4 of 5 people found this instruction helpful.
  • Harlen from Spring Creek, NV
  • Really Easy
  • Less than 15 mins
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.
Was this helpful?
Thank you for voting!
Crazy codes and not heating the oven properly at desired temp settings
3 of 3 people found this instruction helpful.
  • Stan from CHICAGO RIDGE, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. I f you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!
Was this helpful?
Thank you for voting!
Leaking gas from sides of burner
3 of 3 people found this instruction helpful.
  • Homero from SEAGOVILLE, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people found this instruction helpful.
  • Alan from SAN MATEO, CA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Oven wouldn't heat/ turn on
3 of 3 people found this instruction helpful.
  • Diane from NEW HAVEN, MO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
Was this helpful?
Thank you for voting!
Gasket was worn out.
3 of 3 people found this instruction helpful.
  • Michael from VALLEJO, CA
  • Really Easy
  • Less than 15 mins
  • Pliers
Put a new one in.
Was this helpful?
Thank you for voting!
door seal contaminated by a boil-over, not flexible
3 of 3 people found this instruction helpful.
  • Rob from Yakima, WA
  • Really Easy
  • Less than 15 mins
From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.
Was this helpful?
Thank you for voting!
Oven and burners wouldn't light
3 of 3 people found this instruction helpful.
  • Kory from Collingswood, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Easy repair. I removed the module housing at the back of the stove (two screws) and slipped the wires off the old spark module (I had to use pliers to gently pull one or two wires off--it's an old stove). The existing wires slipped right on the new module. I did have to use the mounting adapter that came with the kit, but that was the fiddliest part of the whole repair. It took me longer to move the stove out and back than it did to do the repair.
Was this helpful?
Thank you for voting!
All Instructions for the 3448
106 - 120 of 690