EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3442 - Instructions

All Instructions for the 3442
46 - 60 of 323

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven wouldn't heat.
3 of 3 people found this instruction helpful.
  • Thomas from La Crescenta, CA
  • Easy
  • Less than 15 mins
  • Nutdriver
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pus hed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.
Was this helpful?
Thank you for voting!
OVEN WOULD NOT HEAT
3 of 3 people found this instruction helpful.
  • Mary from MEADVILLE, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Was this helpful?
Thank you for voting!
Self tapping screws stripped out, one broke in mounting hole
3 of 3 people found this instruction helpful.
  • Scott from FORT WORTH, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.
Was this helpful?
Thank you for voting!
Oven ignighter no longer works
3 of 3 people found this instruction helpful.
  • Barry from PORTERVILLE, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel  t ool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!

Barry
Was this helpful?
Thank you for voting!
The inside glass was broken on oven door.
3 of 4 people found this instruction helpful.
  • Jacob from Cotton, MN
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I was pleased with how the job went.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
Was this helpful?
Thank you for voting!
Oven burner would periodically go out and re-light
3 of 4 people found this instruction helpful.
  • Richard from Merrimac, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.
Was this helpful?
Thank you for voting!
Oven taking to long to preheat.
3 of 4 people found this instruction helpful.
  • Isaac from LATHRUP VLG, MI
  • Very Easy
  • 30 - 60 mins
  • Screw drivers
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Was this helpful?
Thank you for voting!
Broiler front drawer slides broke
3 of 4 people found this instruction helpful.
  • Ernie from Fremont, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concis e diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.
Was this helpful?
Thank you for voting!
Oven heat loss, door gasket needed replacement
3 of 4 people found this instruction helpful.
  • Stephen from Chapell Hill, NC
  • Really Easy
  • Less than 15 mins
The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in plac e! Simple!
Was this helpful?
Thank you for voting!
Freont Burners Of Both Units Had Rusted Though Over The Years Of Boilover.
3 of 4 people found this instruction helpful.
  • Angelo W. from Chirfland, FL
  • Really Easy
  • Less than 15 mins
Lifted lid, removed old burner units, replace with new ones. In less than two min. Was back up and cooking.
Was this helpful?
Thank you for voting!
Broiler drawer didn't track poperly
3 of 4 people found this instruction helpful.
  • Keith from Atlanta, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).
Was this helpful?
Thank you for voting!
Oven Was Not Getting Hot
3 of 5 people found this instruction helpful.
  • Joe from Duarte, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I want thank you for being there for me . If it wasn't for you I would be having thanksgiving at my mother inlaw first iremoved the two screwsthat holds thy element in place. I then pulledthe element out about 3 in and disconnected the two wires . It's easy as 1. 2. 3
Was this helpful?
Thank you for voting!
Oven would not ignite
2 of 2 people found this instruction helpful.
  • Dominick from CLARKS SUMMIT, PA
  • Very Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
Very easy, video helped tremendously
Was this helpful?
Thank you for voting!
The oven igniter came on but the gas valve never turned on.
2 of 2 people found this instruction helpful.
  • James from PEORIA, IL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS
Was this helpful?
Thank you for voting!
The problem was exactly what was described on your site.
2 of 2 people found this instruction helpful.
  • William from FREELAND, MI
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. Aft er removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.
Was this helpful?
Thank you for voting!
All Instructions for the 3442
46 - 60 of 323