EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3442 - Instructions

All Instructions for the 3442
31 - 45 of 323

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
30 year old gas stove needed a new burner assembly.
6 of 7 people found this instruction helpful.
  • Caroline from South Windsor, CT
  • Really Easy
  • Less than 15 mins
We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!
Was this helpful?
Thank you for voting!
Faulty bulb receptacle
10 of 20 people found this instruction helpful.
  • Kenneth from Lynchburg, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people found this instruction helpful.
  • Carl from RIVERSIDE, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
Gas manifold had holes in it.
5 of 6 people found this instruction helpful.
  • Mr. J.C. from Haines City, FL
  • Really Easy
  • Less than 15 mins
Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.
Was this helpful?
Thank you for voting!
A high flame was coming out of the side of the burner
5 of 7 people found this instruction helpful.
  • KAY from BRIDGEPORT, CT
  • Really Easy
  • Less than 15 mins
Easy......pulled out the old one easily and popped in the new one.......saved a lot of money...no repair bill for either diagnostic fee or assembly fee ...No mark up for the part either. Very happy mom!
Was this helpful?
Thank you for voting!
oven would not turn on flame
6 of 10 people found this instruction helpful.
  • Michael from Secaucus, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
Was this helpful?
Thank you for voting!
The oven igniter lit up but the valve wouldn't release the gas to ignite.
4 of 4 people found this instruction helpful.
  • John from Wisconsin Rapids, WI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured wi th the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
Was this helpful?
Thank you for voting!
Needed to replace the oven door gasket/seal
4 of 5 people found this instruction helpful.
  • Daniel from Katy, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people found this instruction helpful.
  • peter from marine city, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Was this helpful?
Thank you for voting!
Door gasket was hard and brittle from baked-on grease - heat leaking around door
4 of 5 people found this instruction helpful.
  • Harlen from Spring Creek, NV
  • Really Easy
  • Less than 15 mins
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.
Was this helpful?
Thank you for voting!
Broken levelling leg
5 of 8 people found this instruction helpful.
  • Linda from Oneida, NY
  • Really Easy
  • Less than 15 mins
Took the old levelling leg out and screw the new one in.
Was this helpful?
Thank you for voting!
Broiler drawer front slide plastic guides broke so drawer sagged and was difficult to pull out.
3 of 3 people found this instruction helpful.
  • DOUGLAS from MESA, AZ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the single phillips screw that held each plastic slide guide to the stove, and replaced the part reusing the screws. Was so simple I didn't even have to swear. This was my mother-in-law's stove, and she was so happy to have it repaired she's fed me twice since.
Was this helpful?
Thank you for voting!
door seal contaminated by a boil-over, not flexible
3 of 3 people found this instruction helpful.
  • Rob from Yakima, WA
  • Really Easy
  • Less than 15 mins
From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.
Was this helpful?
Thank you for voting!
Oven wouldn't heat/ turn on
3 of 3 people found this instruction helpful.
  • Diane from NEW HAVEN, MO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
Was this helpful?
Thank you for voting!
Gasket was worn out.
3 of 3 people found this instruction helpful.
  • Michael from VALLEJO, CA
  • Really Easy
  • Less than 15 mins
  • Pliers
Put a new one in.
Was this helpful?
Thank you for voting!
All Instructions for the 3442
31 - 45 of 323