EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3428 - Instructions

All Instructions for the 3428
31 - 45 of 308

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
spark ignition in stove failed to turn on burnes.
7 of 10 people found this instruction helpful.
  • David from Upland, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical. I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Was this helpful?
Thank you for voting!
the lines were broken
7 of 11 people found this instruction helpful.
  • RONALD from DELAVAN, WI
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
1) removed 2 lines 2) removed 4 screws 3)pulled out old element4) relaced new part 5)installed screws 6) install lines &tighten
Was this helpful?
Thank you for voting!
Electronic spark ignition would not ignite intermittently.
5 of 5 people found this instruction helpful.
  • Charles from Old Bridge, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping th e new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.
Was this helpful?
Thank you for voting!
burners corroed by sulphate in the gas
5 of 5 people found this instruction helpful.
  • Juan Jose from Miami, FL
  • Really Easy
  • Less than 15 mins
just turn the burners counter clock wise with the help of a jar opener pad. unplug the wire connectors and replace the burners no hassle, no problem. Everything went fine… one thing though, it is not the same color as it was before. I didn’t realize it until opening the box. Previous color was grey. My wife is Ok with it, so I won’t complain, but maybe you should add the color option if there is more than one choice.

Best regards.
Was this helpful?
Thank you for voting!
both burner heads would not ignite
5 of 6 people found this instruction helpful.
  • Steven from Warwick, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the burner heads from the wires, and simply put the wires on the new burner heads and put back onto the stove,. Simple as pie. Very happy that i found parts select online, easy to find the part though your pictures and easy to order.
Loved being able to do this myself without a middle man. Very satisfied!
Was this helpful?
Thank you for voting!
The oven igniter lit up but the valve wouldn't release the gas to ignite.
4 of 4 people found this instruction helpful.
  • John from Wisconsin Rapids, WI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured wi th the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
Was this helpful?
Thank you for voting!
oven would not turn on flame
6 of 10 people found this instruction helpful.
  • Michael from Secaucus, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
Was this helpful?
Thank you for voting!
Hammered Orifice tubes
4 of 5 people found this instruction helpful.
  • Devin from Santaquin, UT
  • Easy
  • 15 - 30 mins
  • Wrench set
1. Screw the burners counterclockwise 45 degrees to remove each burner. Some gave easily while others were baked on.
2. Remove one philips-head screw per burner.
3. disconnect ignition wire from each burner.
4. remove stovetop.
5. remove the previous hammered orifice and tube assembly by unscrewing 4 nuts.
6. atta ch the new assembly and follow steps 1-4 in reverse order.
Was this helpful?
Thank you for voting!
Needed to replace the oven door gasket/seal
4 of 5 people found this instruction helpful.
  • Daniel from Katy, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.
Was this helpful?
Thank you for voting!
One of four burners did not start (no sparks)
5 of 8 people found this instruction helpful.
  • Nataly from Brooklyn, NY
  • Really Easy
  • Less than 15 mins
Turned burner about a quarter of a turn, lifted, disconnected wires, connected them to a new burner and replaced it.
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people found this instruction helpful.
  • peter from marine city, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Was this helpful?
Thank you for voting!
Door gasket was hard and brittle from baked-on grease - heat leaking around door
4 of 5 people found this instruction helpful.
  • Harlen from Spring Creek, NV
  • Really Easy
  • Less than 15 mins
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.
Was this helpful?
Thank you for voting!
the burner cap on my maytag gas range was rusty on the inside and didn't allow the cap to sit flush-causing gas and flames to leak from under the cap
4 of 5 people found this instruction helpful.
  • julie from harrodsburg, KY
  • Really Easy
  • Less than 15 mins
installation was very simple and took less than 5 minutes. first unscrew the burner cap and then remove the 2 wires. to replace reconnect the 2 wires to the new cap and twist cap into place-simple.
Was this helpful?
Thank you for voting!
Oven and burners wouldn't light
3 of 3 people found this instruction helpful.
  • Kory from Collingswood, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Easy repair. I removed the module housing at the back of the stove (two screws) and slipped the wires off the old spark module (I had to use pliers to gently pull one or two wires off--it's an old stove). The existing wires slipped right on the new module. I did have to use the mounting adapter that came with the kit, but that was the fiddliest part of the whole repair. It took me longer to move the stove out and back than it did to do the repair.
Was this helpful?
Thank you for voting!
door seal contaminated by a boil-over, not flexible
3 of 3 people found this instruction helpful.
  • Rob from Yakima, WA
  • Really Easy
  • Less than 15 mins
From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.
Was this helpful?
Thank you for voting!
All Instructions for the 3428
31 - 45 of 308