3428 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
cracked gas tubes
17 of 21 people
found this instruction helpful.
-
Lance from Overland Park, KS
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
My front burners were inoperative because the metal gas lines under the cooktop were cracked. This happened because I tried to remove the cooktop without properly removing the screws holding the assembly to the cooktop. Doh!
Anyway, this is an easy fix. First, remove the 4 burner tops by rotating them counterclockwise and li ... Read more fting them out of the cooktop. Then, remove the two ignitor wires from each burner, and set the burners aside.
Next, remove the four small screws that hold the burner tube assemblies to the underside of the cooktop. There is one screw near each burner hole in the cooktop (the screws are covered when the burner tops are installed). You must remove all four screws even if you are only installing one replacement orifice and tube kit!
Now you can tilt the cooktop up and remove it from the stove, exposing the orifice and tube assemblies. Use an adjustable wrench to loosen the brass nuts connecting the gas tubes to the valves, and remove the assembly.
Reassemble in reverse order.
If you have "high speed" burners, remove the orifice that comes on the unit and replace it with the loose orifice that is in the packaging.
Anyway, this is an easy fix. First, remove the 4 burner tops by rotating them counterclockwise and li ... Read more fting them out of the cooktop. Then, remove the two ignitor wires from each burner, and set the burners aside.
Next, remove the four small screws that hold the burner tube assemblies to the underside of the cooktop. There is one screw near each burner hole in the cooktop (the screws are covered when the burner tops are installed). You must remove all four screws even if you are only installing one replacement orifice and tube kit!
Now you can tilt the cooktop up and remove it from the stove, exposing the orifice and tube assemblies. Use an adjustable wrench to loosen the brass nuts connecting the gas tubes to the valves, and remove the assembly.
Reassemble in reverse order.
If you have "high speed" burners, remove the orifice that comes on the unit and replace it with the loose orifice that is in the packaging.
Read less
Was this helpful?
Thank you for voting!
Gas oven took longer and longer to light off even though glow igniter was glowing. When the time grew to 10 minutes and more I knew a repair was needed.
15 of 16 people
found this instruction helpful.
-
Joseph from West Hartford, CT
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
I first removed the bottom of the oven and the flame guide to uncover the igniter assembly. Then I applied WD40 to the two Philip head screws and unscrewed them to release the old igniter. The two wire leads from the igniter went into the back of the oven and I could not reach the connection block. So I pulled the oven out far enough to g
... Read more
et behind it and took off the panel covering the electrical wires in back. I had previously disconnected the electrical cord from the wall outlet. After I determined that I could not remove the connection block I returned to the igniter and cut the two existing wires close to the ceramic igniter assembly. I marked the top wire with a Sharpie pen so that I would not mix up the new leads when I install the new igniter. Although it was awkward to work inside the small oven space I was able to strip the insulation back about 1/2 inch and then connect the new igniter wires using the twist caps supplied with the kit. I pushed the wires back into the space and added the insulating material supplied. The igniter assembly was then installed with the original two screws and the other oven covers and flame guide reinstalled easily. After reconnecting the power outlet the oven was back in operation with ignition of gas flame within a minute or so. It was a good feeling and now we do not need to consider replacing the gas range.
Read less
Was this helpful?
Thank you for voting!
Oven stopped while the wife was cooking.
15 of 18 people
found this instruction helpful.
-
Marsha from Concord, MA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws hol ... Read more ding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws hol ... Read more ding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!
Read less
Was this helpful?
Thank you for voting!
Sealed burner caps were rusted within and gas leak through the bottom of the caps
13 of 13 people
found this instruction helpful.
-
j from bridgewater, NJ
- Easy
- 15 - 30 mins
Just used a car oil filter band type wrench and rotated the sealed burner cap a 1/4 turn. cleaned up the rust and dirty. Replaced it with the new cap and tightened it with a 1/4 turn by hand. Instruction can be found on Maytag gas installation manual. The burners are working well and just like a new range.
Was this helpful?
Thank you for voting!
My wife destroyed the oven door seal with oven cleaner...
14 of 16 people
found this instruction helpful.
-
David from Bexley, OH
- Really Easy
- Less than 15 mins
I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its correspon
... Read more
ding hole.
Read less
Was this helpful?
Thank you for voting!
oven won't stay light
10 of 10 people
found this instruction helpful.
-
Shannon from Lake Park, IA
- Easy
- 15 - 30 mins
-
Screw drivers
removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.
Was this helpful?
Thank you for voting!
Cracked gas feed tubes
9 of 11 people
found this instruction helpful.
-
Jeff from Union City, CA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
CAUTION: DO NOT LIFT RANGE TOP AS IT WILL CRIMP YOUR GAS FEED TUBES!!!
Remove grates and drip covers. Twist each burner counter clockwise and lift off. Remove ground wire and ignitor wire from each burner. Remove screws that holds the Orifice/Tube assy to the range top (one where each burner was) You might have to remove the or ... Read more ange rubber flanges if they didn't stay on the burners to see the screws.
Now lift (or remove) your range top to get access to the tube assy. Take a wrench and remove each gas tube nut (2 for each assy) and remove the old assy.
Drop each new Tube assy in and reverse the procedure.
Remove grates and drip covers. Twist each burner counter clockwise and lift off. Remove ground wire and ignitor wire from each burner. Remove screws that holds the Orifice/Tube assy to the range top (one where each burner was) You might have to remove the or ... Read more ange rubber flanges if they didn't stay on the burners to see the screws.
Now lift (or remove) your range top to get access to the tube assy. Take a wrench and remove each gas tube nut (2 for each assy) and remove the old assy.
Drop each new Tube assy in and reverse the procedure.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 8 people
found this instruction helpful.
-
Treasure from High Point, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
Read less
Was this helpful?
Thank you for voting!
Oven would not heat but Broiler would
8 of 9 people
found this instruction helpful.
-
Robert from Hudson, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Turn off the gas supply and unplug the power cord. Remove the screw on the back plate for the metal tab that covers the valve. Bend the tab up to expose the valve. Remove the gas line that feeds the broiler with an adjustable wrench. Remove the mounting screw for the valve. Loosen the valve inlet gas line fitting with an adjustable wr
... Read more
ench. Lift the valve out. Reverse the steps to install the new valve.
Read less
Was this helpful?
Thank you for voting!
the burner knobs broke off
10 of 17 people
found this instruction helpful.
-
Belinda from Downey, CA
- Really Easy
- Less than 15 mins
I put the 2 burner knobs on and now I have 4 working burners....Thanks for the quick delivery....
Was this helpful?
Thank you for voting!
Oven floor panel was warped.
8 of 11 people
found this instruction helpful.
-
Cindy from Colton, CA
- Really Easy
- Less than 15 mins
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 11 people
found this instruction helpful.
-
John from Caliente, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Parts came very quickly from PartSelect. Good service.
Was this helpful?
Thank you for voting!
Oven would stop heating after a few minutes of operation
6 of 6 people
found this instruction helpful.
-
John from Ashland, OR
- Easy
- Less than 15 mins
-
Pliers
Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull
... Read more
the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.
Read less
Was this helpful?
Thank you for voting!
Burners would not ignite
6 of 7 people
found this instruction helpful.
-
Charles from Kalamazoo, MI
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed cover from igniter, took off wires, replaced wires on new one, secured in place, put cover back on.
Was this helpful?
Thank you for voting!
Igniters were flaky on 2 burners and almost dead on 2
7 of 10 people
found this instruction helpful.
-
Matt from Craig, CO
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the uti
... Read more
lity drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Read less
Was this helpful?
Thank you for voting!