EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3287 - Instructions

All Instructions for the 3287
91 - 105 of 292

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Gas would come on, would not ignite. Oven not heating.
1 person found this instruction helpful.
  • Karen from DAYTON, OH
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Was this helpful?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
1 person found this instruction helpful.
  • Mz from COLUMBIA, ME
  • Very Easy
  • Less than 15 mins
  • Pliers
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this helpful?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
1 person found this instruction helpful.
  • Tara from ALBANY, NY
  • Easy
  • 15 - 30 mins
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this helpful?
Thank you for voting!
The oven igniter would glow red but gas did not come on to light the burner.
1 person found this instruction helpful.
  • Ernest from CINCINNATI, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this helpful?
Thank you for voting!
My oven door seal had dried rotted
1 person found this instruction helpful.
  • Anita from ELKTON, VA
  • Really Easy
  • 15 - 30 mins
  • Pliers
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this helpful?
Thank you for voting!
Simply remove and install new parts
1 person found this instruction helpful.
  • Jacob from LITTLE CANADA, MN
  • Really Easy
  • 15 - 30 mins
Overall, it was painless and easy with zero problems
Was this helpful?
Thank you for voting!
Oven would'nt heat
1 of 2 people found this instruction helpful.
  • Ariel from Oxford, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver
First I removed the two screws that held the old element in place. I then pulled the element out about 3 inches and disconnected the two wires.
I replaced the element with the new one and tucked the connector in the insulation. Additional insulation came with the kit. I replaced the two screws that held the element in placed. Oven wo rked perfectly
Was this helpful?
Thank you for voting!
Oven did not ignite
1 of 2 people found this instruction helpful.
  • John from Racine, WI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..
Was this helpful?
Thank you for voting!
Igniter Would Glow But Stove Wouldn't Light
1 of 2 people found this instruction helpful.
  • ALAN from LUCK, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I noticed that the ignitor would glow but the stove wouldn't light - I got the model number of the stove and googled the maytag model number. Came upon your website and realized that 94% of the time the problem was the amps were not enough to light the stove. I looked at all of the stories on how easy it was to fix. I ordered the pa rt and received it within 3 days. I opened the door part way and lifted it straight up to remove it. I pulled out the bottom broiler plate by grabbing the back on pulling up. I undscrewed the wing nut of the flame bar and had easy access to the igniter. I removed the two nuts from the old igniter. Unplugged the igniter from the easy access door from the back and plugged in the new igniter. Replaced the access door and attached the igniter with the two nuts. Put the flame bar back on, put the broiler plate back on, put the door back on, plugged in the stove turned it on and success. It was so easy. I know in our area I would have paid near $200 for a service technician to come out and do what I did in approx. 20 Minutes and $50 for the part. Thank you so much for you website to help us not so talented appliance repair homeowners.
Was this helpful?
Thank you for voting!
my stovetop light did not work
1 of 2 people found this instruction helpful.
  • Geraldine M. from Fork Union, VA
  • Really Easy
  • 15 - 30 mins
We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No applianc e store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Was this helpful?
Thank you for voting!
Oven Ignitor went to ignitor heaven.
1 of 2 people found this instruction helpful.
  • Brian from Pittsburgh, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Socket set
The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I wou ld absolutely use your services again. Oven is back to working great! Thank you!
Was this helpful?
Thank you for voting!
Bottom oven burner wouldn't light.
1 of 2 people found this instruction helpful.
  • James from Lino Lakes, MN
  • Easy
  • Less than 15 mins
  • Nutdriver
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.
Was this helpful?
Thank you for voting!
old tube burned out
2 of 5 people found this instruction helpful.
  • JERRY from SPANISH FORK, UT
  • Really Easy
  • Less than 15 mins
removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.
Was this helpful?
Thank you for voting!
Oven wouldn't heat. Igniter was broken.
1 of 2 people found this instruction helpful.
  • Thomas from Allison Park, PA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
Was this helpful?
Thank you for voting!
Stove top burners ignition were not working
1 of 2 people found this instruction helpful.
  • Jeffrey from Somonauk, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
1st unplug stove opened cover to wireing box with a phillips driver removed old part transfered wires one by one installed new part installed cover & pluged in stove & worked line new.
Was this helpful?
Thank you for voting!
All Instructions for the 3287
91 - 105 of 292