EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3287 - Instructions

All Instructions for the 3287
76 - 90 of 292

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
original fixture required bulb - this fixture (all-in-one) was great
1 person found this instruction helpful.
  • wesley from ODENVILLE, AL
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.
Was this helpful?
Thank you for voting!
Igniter was not getting hot enough to allow burner to come on.
1 person found this instruction helpful.
  • ELMER from BONNEY LAKE, WA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
Was this helpful?
Thank you for voting!
Burners would not lite
2 of 4 people found this instruction helpful.
  • Lloyd from Cocoa, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped.      Thanks   Lloyd
Was this helpful?
Thank you for voting!
No heat in oven
1 person found this instruction helpful.
  • Cynthia from AURORA, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this helpful?
Thank you for voting!
Oven would not start, ignitor was not doing anything
1 person found this instruction helpful.
  • Michael from Syracuse, NY
  • Easy
  • 15 - 30 mins
  • Wrench set
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up an d then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
Was this helpful?
Thank you for voting!
broke the igniter in the oven before I even got the oven installed
1 person found this instruction helpful.
  • june from wills point, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Was this helpful?
Thank you for voting!
no spark on top burners
2 of 4 people found this instruction helpful.
  • eric from winter haven, FL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.
Was this helpful?
Thank you for voting!
Oven was slow to get to temp and not holding temp
1 person found this instruction helpful.
  • Matt from Arlington, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.
Was this helpful?
Thank you for voting!
Stove Would Not Light To Heat Up.
1 person found this instruction helpful.
  • Nola from Enid, OK
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this helpful?
Thank you for voting!
None
1 person found this instruction helpful.
  • Dhirajlal from SKOKIE, IL
  • Very Easy
  • Less than 15 mins
Located holes, lined up the pins and pushed it in. Perfect fit.
Was this helpful?
Thank you for voting!
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
1 person found this instruction helpful.
  • FRANCES from AFFTON, MO
  • Very Easy
  • Less than 15 mins
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this helpful?
Thank you for voting!
oven would not heat up fully, smelled of gas.
1 person found this instruction helpful.
  • Brian from Spotswood, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this helpful?
Thank you for voting!
oven would not light reliably.
1 person found this instruction helpful.
  • Joe from West Winfield, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this helpful?
Thank you for voting!
Igniter for oven not working
1 person found this instruction helpful.
  • RONNIE from SAG HARBOR, NY
  • Easy
  • Less than 15 mins
  • Wrench set
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this helpful?
Thank you for voting!
igniter failed to ignite
1 person found this instruction helpful.
  • Gino from ARLETA, CA
  • Really Easy
  • Less than 15 mins
  • Socket set
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this helpful?
Thank you for voting!
All Instructions for the 3287
76 - 90 of 292