3227 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven wouldn't heat.
3 of 3 people
found this instruction helpful.
-
Thomas from La Crescenta, CA
- Easy
- Less than 15 mins
-
Nutdriver
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pus
... Read more
hed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat/ turn on
3 of 3 people
found this instruction helpful.
-
Diane from NEW HAVEN, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first
... Read more
turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
Read less
Was this helpful?
Thank you for voting!
Leaking gas from sides of burner
3 of 3 people
found this instruction helpful.
-
Homero from SEAGOVILLE, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.
Was this helpful?
Thank you for voting!
OVEN WOULD NOT HEAT
3 of 3 people
found this instruction helpful.
-
Mary from MEADVILLE, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Was this helpful?
Thank you for voting!
Gas was escaping from underneath the burner head
3 of 3 people
found this instruction helpful.
-
Edward from ALEXANDRIA, VA
- Easy
- 30 - 60 mins
-
Pliers
The old burner head had corroded allowing gas to come out at the bottom. The actual replacement is just turning the head, lifting it out, transferring two wires with slip-on connectors from the old burner to the new one, and dropping the new one in place. Most of the time was spent sanding away corroded metal on the base to make a good
... Read more
fit. The information on the burner head says that the company has decided not to use a gasket under the head. I suggest that was a bad decision.
Read less
Was this helpful?
Thank you for voting!
Self tapping screws stripped out, one broke in mounting hole
3 of 3 people
found this instruction helpful.
-
Scott from FORT WORTH, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.
Was this helpful?
Thank you for voting!
Oven ignighter no longer works
3 of 3 people
found this instruction helpful.
-
Barry from PORTERVILLE, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel t
... Read more
ool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!
Barry
Barry
Read less
Was this helpful?
Thank you for voting!
Oven burner would periodically go out and re-light
3 of 4 people
found this instruction helpful.
-
Richard from Merrimac, MA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- ... Read more Connect the new part
- Re-attach to the bracket with new screws.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- ... Read more Connect the new part
- Re-attach to the bracket with new screws.
Read less
Was this helpful?
Thank you for voting!
Oven taking to long to preheat.
3 of 4 people
found this instruction helpful.
-
Isaac from LATHRUP VLG, MI
- Very Easy
- 30 - 60 mins
-
Screw drivers
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Was this helpful?
Thank you for voting!
igniter burned out
2 of 2 people
found this instruction helpful.
-
David from Milton, MA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.
Was this helpful?
Thank you for voting!
oven would not light
2 of 2 people
found this instruction helpful.
-
gary from covington, LA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.
Was this helpful?
Thank you for voting!
1960's oven door gasket fell apart, actual gasket not available any more
2 of 2 people
found this instruction helpful.
-
Mary from WINCHESTER, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Was this helpful?
Thank you for voting!
floor panel heavily stained and warped
3 of 5 people
found this instruction helpful.
-
Joel from Monroe, NY
- Really Easy
- Less than 15 mins
slide latches in rear of floor panel forward and remove.
Was this helpful?
Thank you for voting!
Broken burner - easy fix
2 of 2 people
found this instruction helpful.
-
Don from NEW YORK, NY
- Really Easy
- 15 - 30 mins
-
Pliers
The burner was leaking a rust colored dirt and shooting flames all over the place. The top came off and I needed channel-locks to get the bottom half out. The wires were hard to get off and I broke one connector off so I soldered the wire on to the new part which fit the stove top perfectly. It still took less than a half hour to repla
... Read more
ce. Without problems it should take about 5 minutes.
Read less
Was this helpful?
Thank you for voting!
Burner igniter problem.
2 of 2 people
found this instruction helpful.
-
Dhirajlal from SKOKIE, IL
- Really Easy
- 15 - 30 mins
-
Pliers
Replaced with a new one.
Was this helpful?
Thank you for voting!