EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3227 - Instructions

All Instructions for the 3227
16 - 30 of 263

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner head was rusted out. ordered 1 to see if part was correct. ordered 4 more to finish job.
13 of 17 people found this instruction helpful.
  • Robert from Somerville, TN
  • Really Easy
  • Less than 15 mins
unscrewed old burner head ;disconnected 2 wires; repaced with new burner head and replaced wires. Unfortunately, before we really needed to replace the other burner heads, the cooktop itself developed a gas leak. We decided to replace the whole thing, and therefore would like to return the unboxed, unused 4 remaining burner heads.
Was this helpful?
Thank you for voting!
Spring on hinge broke. Door wont close totally
12 of 15 people found this instruction helpful.
  • Thomas from Baton Rouge, LA
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set
Using the description on the first DIY, I did as told. All went well until the part about removing the panel to access the hinge. There isn't a "panel" on the side of this particular model of Magic Chef stove. You have to remove the entire side of the stove, and then, there's another panel inside of this one. That too has to come off. On ce off, you're into the insulation surrounding the oven. Ain't pretty, I'll assure you. Then, the replacement hinge has holes in it for the mounting screws. The holes aren't threaded, and you have to replace the screws that come with the hinge with self-tapping screws. Either that, or thread the holes with a tap. Thank goodness my wife loves the stove, or it may have just gone out the door. This is not one of Magic Chefs better ideas. Either that, or they didn't plan on having to replace the hinge before the stove wore out.
Was this helpful?
Thank you for voting!
oven won't stay light
10 of 10 people found this instruction helpful.
  • Shannon from Lake Park, IA
  • Easy
  • 15 - 30 mins
  • Screw drivers
removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.
Was this helpful?
Thank you for voting!
Door Seal on oven was old, hard and breaking apart.
10 of 11 people found this instruction helpful.
  • Kenneth from Friend, NE
  • Really Easy
  • Less than 15 mins
  • Pliers
It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 8 people found this instruction helpful.
  • Treasure from High Point, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
Was this helpful?
Thank you for voting!
Seal was fallinig off
7 of 8 people found this instruction helpful.
  • Marilyn from Fresno, CA
  • Really Easy
  • Less than 15 mins
My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.
Was this helpful?
Thank you for voting!
Oven floor panel was warped.
8 of 11 people found this instruction helpful.
  • Cindy from Colton, CA
  • Really Easy
  • Less than 15 mins
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 11 people found this instruction helpful.
  • John from Caliente, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.
Was this helpful?
Thank you for voting!
Bad Door Gasket.
6 of 8 people found this instruction helpful.
  • Donald from Schuylkill Haven, PA
  • Really Easy
  • Less than 15 mins
  • Pliers
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.
Was this helpful?
Thank you for voting!
Faulty bulb receptacle
10 of 20 people found this instruction helpful.
  • Kenneth from Lynchburg, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!
Was this helpful?
Thank you for voting!
Stove seal fell apart
5 of 6 people found this instruction helpful.
  • Teresa from Washougal, WA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.
Was this helpful?
Thank you for voting!
oven would not turn on flame
6 of 10 people found this instruction helpful.
  • Michael from Secaucus, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
Was this helpful?
Thank you for voting!
The oven igniter lit up but the valve wouldn't release the gas to ignite.
4 of 4 people found this instruction helpful.
  • John from Wisconsin Rapids, WI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured wi th the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people found this instruction helpful.
  • peter from marine city, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Was this helpful?
Thank you for voting!
oven door gasket torn
4 of 5 people found this instruction helpful.
  • Ovide N from Abbeville, LA
  • Really Easy
  • Less than 15 mins
ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job
Was this helpful?
Thank you for voting!
All Instructions for the 3227
16 - 30 of 263