32-25 Tappan Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
igniter replacement
0 of 1 people
found this instruction helpful.
-
Brianna from Livonia, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
followed online instructions
Was this helpful?
Thank you for voting!
Oven would not ignite to heat to baking temperature
0 of 1 people
found this instruction helpful.
-
Louise from Delaware, OH
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
pulled stove out to unplug the electric cord. Took oven door off and removed the bottom panel (2 screws) and then removed the burner (2 screws). took off old igniter ( 2 nut screws). cut wires and stripped the coating to wire to new unit.
Attached new igniter to the burner, and put the burner back in place and replaced the screws ... Read more so unit was stable.
Turned oven on to make sure ingiter was going to light oven, when oven came on, turned oven off and replaced the cover to the burner and the bottom panel in the oven,. Put the oven door back on........
Probably took 45 minutes.
I ordered the part late Friday afternoon, around 3, and the part was here Saturday Afternoon. I was impressed.
Attached new igniter to the burner, and put the burner back in place and replaced the screws ... Read more so unit was stable.
Turned oven on to make sure ingiter was going to light oven, when oven came on, turned oven off and replaced the cover to the burner and the bottom panel in the oven,. Put the oven door back on........
Probably took 45 minutes.
I ordered the part late Friday afternoon, around 3, and the part was here Saturday Afternoon. I was impressed.
Read less
Was this helpful?
Thank you for voting!
The oven igniter no longer worked
0 of 1 people
found this instruction helpful.
-
Ralph from East Brunswick, NJ
- A Bit Difficult
- 30 - 60 mins
-
Pliers
Let me begin to say your service was great. I received the unit the next day. Also your price was good.
The whole job took me an hour. I would have done it sooner but I didnt a square head driver bit to remove the igniter from the burner assembly. I removed the whole assembly and with a pliers slowly unscrewed the mounting screws. Af ... Read more ter that I disconnected the igniter per your instructions,spliced the remaining wires reconnected the gas and electric and I was good to go.
The whole job took me an hour. I would have done it sooner but I didnt a square head driver bit to remove the igniter from the burner assembly. I removed the whole assembly and with a pliers slowly unscrewed the mounting screws. Af ... Read more ter that I disconnected the igniter per your instructions,spliced the remaining wires reconnected the gas and electric and I was good to go.
Read less
Was this helpful?
Thank you for voting!
Oven was slow to light, strong gas smell, long time to reach set temperature
0 of 1 people
found this instruction helpful.
-
Gary Warren from Alexandria, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.
It was a snap!
It was a snap!
Was this helpful?
Thank you for voting!
My oven would glow, but wouldn't heat.
0 of 1 people
found this instruction helpful.
-
Steve from Macomb, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.
In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor ... Read more by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.
The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.
In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor ... Read more by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.
The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat up
0 of 1 people
found this instruction helpful.
-
Steve from Canton, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.
to oven igniter, but igniter was not glowing.
Was this helpful?
Thank you for voting!
perheat light stayed on, oven never came on.
0 of 1 people
found this instruction helpful.
-
john from snowflake, AZ
- Really Easy
- 30 - 60 mins
-
Screw drivers
followed the instructions that come with the part. very quick and easy.
Was this helpful?
Thank you for voting!
oven whouldn't come on or if it did it whould take along time to come on and stop after awhile
0 of 1 people
found this instruction helpful.
-
Ralph from Garfield Hts., OH
- Really Easy
- 30 - 60 mins
-
Socket set
pulled bottom door out as far as you can. lift out broiler tray and the tray under that. to get the door completely out. on each side of the rail holding the door from come out push in the tap on each side and pull the door all the way out and off. reach inside and take out two nuts holding the old igniter and cut the two wires and remove
... Read more
it
stripe about 1/4 in of the wire. attache the wire from the new igniter. hold them two and use the white cap and twist it on the two wires and do the same to the other two wires. Bolt the igniter back on with the two bolts and your done. When you turn on the oven the igniter will click and turn on. it will be alot brighter then the old one and the oven will start pretty fast.
stripe about 1/4 in of the wire. attache the wire from the new igniter. hold them two and use the white cap and twist it on the two wires and do the same to the other two wires. Bolt the igniter back on with the two bolts and your done. When you turn on the oven the igniter will click and turn on. it will be alot brighter then the old one and the oven will start pretty fast.
Read less
Was this helpful?
Thank you for voting!
Oven Would Not Light
0 of 1 people
found this instruction helpful.
-
Neil W. from Westerville, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I replaced both gas valve and igniter. I removed oven door and bottom of oven for easy access to both. The door slid off easy and the bottom was held by two thumb screws. I removed the gas flare for easy access to igniter & valve. I then removed the igniter & valve using nutdriver, phillips screwdriver and adj wrench. I then followed
... Read more
simple instructions supplied for wire connect on igniter and valve. It was a very easy job for a 25 yr old stove. I made the mistake of ordering only the valve and ordered the igniter later. Having both new parts causes the oven to light in about 30 seconds. Im glad I found partselect online. Nh, westerville, oh
Read less
Was this helpful?
Thank you for voting!
Oven stopped lighting
0 of 1 people
found this instruction helpful.
-
DAVID from Marina, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I simply searched YouTube for the problem I was having and foud it was probably caused by a bad part. I found the part online and ordered it. It was as simple as a few screws and a couple wire-nuts to install. My girlfrind was very happy to get the oven fixed !!!!
Thanks parts-select for having pictures and dimensions so I ... Read more was sure I had ordered the exact right part.
I was soooo happy to have found you !
Thanks parts-select for having pictures and dimensions so I ... Read more was sure I had ordered the exact right part.
I was soooo happy to have found you !
Read less
Was this helpful?
Thank you for voting!
Oven Burner Would Not Ignite. Heard the controls click to start oven but no fire.
0 of 1 people
found this instruction helpful.
-
Mark from Rockford, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Unplug appliance. Remove the bottom of the oven (2 screws in back of oven bottom), remove burner cover (2 screws in front and nut in center holding burner). Pull out the bottom storage drawer under the oven and unplug both wires from oven Igniter which are located in the back. One wire plugs into the gas valve and the second wire went
... Read more
into a connector that was on the lower left. I removed the screw on the back oven wall that held the burner so I could remove the burner for ease of work. Remove two screws holding the old igniter. The two screws holding the igniter to the side of the burner were stripped and they took a little time to remove but I replaced them with two new screws I had in my misc. screw drawer and had no issue. Cut the top wire and splice it onto the top wire of the new igniter using the porcelain wire nuts provided. Do the same with the bottom wire. Re-assemble and plug back in. Everything worked perfectly.
Read less
Was this helpful?
Thank you for voting!
Gas valve would not turn on.
0 of 1 people
found this instruction helpful.
-
Todd from Matteson, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Socket set
I exposed the ignitor through the inside of the oven and then removed the two screws that held it in place. I then cut the wires underneath the stove ans reconnected them to the new part with the wire nuts provided. It was a simple repair.
Was this helpful?
Thank you for voting!
Replace the oven igniter
0 of 1 people
found this instruction helpful.
-
Mike from Hamburg, NY
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Remove the oven drip pan & burner baffle. unscrew & cut leads to remove old igniter. Splice old leads to new using furnished wire nuts and remount. Job would have been easier with oven door removed, but didnt want to create a new project.
Was this helpful?
Thank you for voting!
The oven would no longer light
0 of 1 people
found this instruction helpful.
-
Sherry from New Smyrna Beach, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
My husband was able to easily remove the old part, and replace with the new ignitor. The wires were long, so he took the extra precaution of tying them away from the flame. It took longer to take everything out and put it back together than the actual repair..
Was this helpful?
Thank you for voting!
Gas oven would take forever to light and would not relight if cooking temp was reduced
0 of 1 people
found this instruction helpful.
-
John from Newmarket, NH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
1. Unplugged power cord.
2. Removed warming drawer and oven shelves and lower plate
3. Removed old wirenuts from back of warming draw space (awkward to reach in to the back).
4. Removed 2 screws holding ignitor in oven - screws in poor shape and were not reuseable.
5. Found next size up sheetmetal screws and installed ... Read more new ignitor.
6. Ran wires down adjacent to gas feed into warming drawer space.
7. Connected with wirenuts supplied with ignitor.
8. Replaced everything.
9. Tested oven and ate some tasty blueberry muffins.
2. Removed warming drawer and oven shelves and lower plate
3. Removed old wirenuts from back of warming draw space (awkward to reach in to the back).
4. Removed 2 screws holding ignitor in oven - screws in poor shape and were not reuseable.
5. Found next size up sheetmetal screws and installed ... Read more new ignitor.
6. Ran wires down adjacent to gas feed into warming drawer space.
7. Connected with wirenuts supplied with ignitor.
8. Replaced everything.
9. Tested oven and ate some tasty blueberry muffins.
Read less
Was this helpful?
Thank you for voting!