EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

32-25 Tappan Range - Instructions

All Instructions for the 32-25
106 - 120 of 277

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
my oven wouldn't light
1 person found this instruction helpful.
  • david from granville summit, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
first i removed the bottom of the oven [inside the oven] ,the part was right there,i removed 2 screws and unpluged the wires,then i cut the wire ends off the old part and used the wirenuts that came with the new one to hook them to the new part,then put it back in place,put the screws back in put the bottom back in and was done
Was this helpful?
Thank you for voting!
Oven would not light
1 person found this instruction helpful.
  • Stephen from Pittsburgh, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!
Was this helpful?
Thank you for voting!
replaced theoriginal power cord.
1 person found this instruction helpful.
  • Blanca from Union City, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.
Was this helpful?
Thank you for voting!
The oven would not light and the house smelled like gas.
1 of 2 people found this instruction helpful.
  • Jeffrey from Mission Viejo, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I removed the oven floor and subfloor. I detached the old ignighter leaving the wires still attached. I then attached the new ignighter and fed each of the two new wires down through the bottom of the oven floor following the same path of the old wires which were still attached. I attached the new wires one at a time to make sure I connec ted them to the right place. Then, I pulled out the old igniter. I then attached the oven floors and turned the oven on which now works. The tough part is pulling the oven out from the wall to disconnect the power and turn off the gas. I did not remove the oven door.
Was this helpful?
Thank you for voting!
Oven would not come on. If it did, it took a long time to heat up.
1 of 2 people found this instruction helpful.
  • Frank from Greenbackville, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed the broiler compartment door by depressing the slide stops inward and pulling the door off. Turned off the breaker to the oven. Used a nut driver to remove the old ignitor ( 2 screws ). Cut the wires off the old ignitor close to the porclin. Measured the new ignitor wires to match up with the old ignitor wires and cut them. St ripped 3/8 " off ends of newely cut wires of the ignitor and used the supplied wire nuts to secure them together. Replaced the new ignitor with the 2 screws. Turned on the oven and a cooking I went.
Was this helpful?
Thank you for voting!
Oven wouldn't come on
1 of 2 people found this instruction helpful.
  • Arthur L from Huntington, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.
Was this helpful?
Thank you for voting!
Oven wouldn't heat , glow from bottom, and strong smell of gas
1 of 2 people found this instruction helpful.
  • Clayton from Gulf Breeze, FL
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers, Wrench set
First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two sc rews on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.
Was this helpful?
Thank you for voting!
no flame at the burner
1 of 2 people found this instruction helpful.
  • Michael from Cardiff, CA
  • Really Easy
  • Less than 15 mins
snapped the old burner out of the snap fixture on the range lid. snapped the new burner into place. done! voila - I created fire!
Was this helpful?
Thank you for voting!
Oven thermostat knob lost or broken
1 of 2 people found this instruction helpful.
  • Hope from Jamaica Plain, MA
  • Really Easy
  • Less than 15 mins
An all-purpose hardware-store knob didn't work, the shaft was way too short.With the aid of the Part-Select diagram,I found the correct stove model number. The simple little Tappan oven control knob cost over $30. I checked other appliance part vendors on-line, but found their part descriptions imprecise and equally expensive. I ordered the part and it arrived in 2 days and worked perfectly. An appliance store had told me I wouldn't find a retrofit on such an old stove and I would have to buy a new stove!
Was this helpful?
Thank you for voting!
the oven was slow to light and didn't reach the set temperature
1 of 2 people found this instruction helpful.
  • James from Chicago, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.
Was this helpful?
Thank you for voting!
Ignition not working
1 of 2 people found this instruction helpful.
  • Ricardo from Stamford, CT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Ins talled new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.
Was this helpful?
Thank you for voting!
light bilb went out
2 of 6 people found this instruction helpful.
  • Denise from Landover, MD
  • Really Easy
  • Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
Igniter lights up, but no flame appears, no gas
1 of 3 people found this instruction helpful.
  • Denise from Clinton Township, MI
  • Really Easy
  • More than 2 hours
I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, w orked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,
Was this helpful?
Thank you for voting!
The igniter would glow but the gas would not come on.
0 of 1 people found this instruction helpful.
  • ernest from mays landing, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I removed the oven bottom which was held by two large head long screws. I then removed the heat deflector using a small socket. The only difficult part was when I went to replace the igniter. The screws that were holding it in place stripped I guess do to the amount of heat they were continually subject too. I had to apply pressure to the igniter bracket while removing the screw using a small socket. Even with that they did not come out easily. If I had not had trouble removing the screws the repair probably would have taken 15 min.
Was this helpful?
Thank you for voting!
oven slow to warm and gas smell
0 of 1 people found this instruction helpful.
  • JONATHAN from DEARBORN, MI
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Removed lower burner covers and fan cover to access igniter. Unscrewed igniter and pulled out as far as possible. Marked both wires and snipped them. Twisted on wires from new igniter and mounted igniter. Pulled excess wire thru to back of oven and reassembled covers from first step. Last step was to explain to wife that she needs clean i n there MUCH better.
Was this helpful?
Thank you for voting!
All Instructions for the 32-25
106 - 120 of 277