32-01 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven wouldn't heat, made noises
0 of 1 people
found this instruction helpful.
-
Marvin from Woodbridge, CT
- Easy
- 15 - 30 mins
-
Nutdriver
First I'll say the instructions and comments from this site were right on, making it easy. I slid the oven out and unplugged the electric. Opened the door, took out the racks, took out the two thumbscrews at the back bottom and lifted the bottom plate up and out, and lifted off the heat guard plate. I could then see and reach the ignite
... Read more
r pretty easily (the flashlight helped). The igniter may have been replaced before because there were already wire nuts on the wires. I unscrewed the two screws using the nutdriver and noted which wire (top or bottom) went to which wire inside. Unscrewed the wire nuts and removed the old igniter. Used the old igniter to determine where to cut and strip the new igniter's wires. Connected the wires of the new igniter using the wire nuts and put the two mounting screws in. Then just put all the other stuff back in (heat guard, bottom plate/two thumbscrews, racks). Plugged it in and started the oven. Got a small amount of "crackly" noise initially (maybe because the igniter was new) but that went away and it's been working fine and quiet since. Very easy (well, perhaps other than being on your knees, leaned into the back of an oven for a couple minutes). Well worth the effort.
Read less
Was this helpful?
Thank you for voting!
Oven not heating and theres a smell of gas.
0 of 1 people
found this instruction helpful.
-
Ken from Fresno, TX
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
1. Unplugged unit and shut gas off.
2. Removed the oven door(2screws).
3. Removed the oven floor(3screws).
4. Removed heat dispersion plate(1bolt).
5. Removed faulty igniter(2screws).
6. Labeled and spliced wires.
7. Connected new igniter.
8. Installed all previously removed parts.
9. Restored power ... Read more and gas to unit and oven
fired up in a matter of seconds.....Thanks
2. Removed the oven door(2screws).
3. Removed the oven floor(3screws).
4. Removed heat dispersion plate(1bolt).
5. Removed faulty igniter(2screws).
6. Labeled and spliced wires.
7. Connected new igniter.
8. Installed all previously removed parts.
9. Restored power ... Read more and gas to unit and oven
fired up in a matter of seconds.....Thanks
Read less
Was this helpful?
Thank you for voting!
oven would not light
0 of 1 people
found this instruction helpful.
-
Gerald from Scotia, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
suspected oven ignitor,went to partselect website and saw
others had same concern and ignitor was the failed part.ignitor was not getting white hot just orange-not enough
voltage going to the gas valve to open it.ordered and replaced
ignitor.repair took about 20 minuets-oven repaired.
others had same concern and ignitor was the failed part.ignitor was not getting white hot just orange-not enough
voltage going to the gas valve to open it.ordered and replaced
ignitor.repair took about 20 minuets-oven repaired.
Was this helpful?
Thank you for voting!
no flame
0 of 1 people
found this instruction helpful.
-
joe from newport beach, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
removed the old igniter, installed the new one. 15 minutes, piece o cake!
Was this helpful?
Thank you for voting!
Had a problem igniting the gas.
0 of 1 people
found this instruction helpful.
-
Danny from Bremerton, WA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
took the old igniter out and swapped the connectors onto the new one. Kept the connectors close to the connector end to prevent them from being to close to the ovens heat.
Was this helpful?
Thank you for voting!
glo plug wouldn/t ignite
0 of 1 people
found this instruction helpful.
-
William from Smyrna, DE
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took out the old (2 screws) put clip on wires and put the new part in. Simple
Was this helpful?
Thank you for voting!
Oven would not heat up
0 of 1 people
found this instruction helpful.
-
Bobby from Bonnerdale, AR
- Easy
- 15 - 30 mins
-
Screw drivers
Figured out which part we needed by reading about others problems; Followed instructions & Presto = oven heats!!!! Didn't have any problems removing or replacing part.
Was this helpful?
Thank you for voting!
oven would not heat up smell of gas
0 of 1 people
found this instruction helpful.
-
peter from bronx, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
i followed some of the tips provided, and added a few of my own. unplug stove from electric outlet. open oven door, remove wire trays. remove the two flathead screws, holding down the oven pan, it should slide out easily. remove oven burner(looks like wings)only one nut holding it in place with 1/4"nutdriver. remove igniter, 2 nuts as wel
... Read more
l with 1/4" nutdriver. cut wires, leave a good length, and strip(2 wires). install new igniter, strip the 2 wires as well, trim to size, and with the two wire caps provided, make wire connections. tuck any excess length of wires away from igniter. re-install all parts the were orginally removed. plug oven back into outlet. turn on oven, and presto, oven worked good as new. saved a couple of hundred dollars doing the repair myself
Read less
Was this helpful?
Thank you for voting!
Top part of stove worked but not the oven
0 of 1 people
found this instruction helpful.
-
PAULA from AUSTIN, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
I googled most of the problem I was having. When I would turn on the oven I would have the orange glow from the igniter but I would never get heat. I ordered the part off this website...it arrived the very next day!!! 7 months pregnant I fixed the problem!!! My oven works beautifuly!! Just in time for the holidays! I saved so so muc
... Read more
h money doing it myself. U to can do it, good luck!!
Read less
Was this helpful?
Thank you for voting!
oven would not ignite
0 of 1 people
found this instruction helpful.
-
Derrick from Houston, TX
- Really Easy
- 15 - 30 mins
-
Socket set
after reading other replies i was 100 percent sure that my igniter was the problem . just as others said it had a veryh dem glow . once i changed it the oven lit in about 5 seconds .very easy to install and saved at lease $ 400 on not needing a new stove. thanks parts select . com
Was this helpful?
Thank you for voting!
Oven would not come on
0 of 1 people
found this instruction helpful.
-
Jim from Merced, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
From the front I cut the wires going to the old igniter and removed it. Then I stripped insulation back 3/8 of an inch. Using the ceramic wire nuts that came with the new igniter, I connected the new wires to the existing. Then I installed the new igniter and the job was done. I turned on the thermostat and the oven ignited quicker than i
... Read more
t had for some time.
Read less
Was this helpful?
Thank you for voting!
oven wouldn't light
0 of 1 people
found this instruction helpful.
-
matthew from Plainfield, IL
- Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I
... Read more
was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.
Read less
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people
found this instruction helpful.
-
Kenneth from Valencia, CA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
1st took out switch from thermostat unit, located right on the other side of where the temperature knob is located (that controls cooking temp of the oven). Had to lift up range cover to get to the thermostat. Tested this switch with a meter and found it was OK. This made me suspect the igniter, so I ordered one.
To install I fi ... Read more rst unplugged oven (to prevent getting shocked) then took off the drawer on the bottom compartment (push in on tabs on rails until they release). Then take out two screws holding igniter. Mark wires with tape so you know which one goes to the upper part of the igniter and which one goes to the lower part. Then cut wires as close to the body of the igniter as you can so that you have plenty of wire to work with. Then hold igniter in about the place it will be mounted and mark the wires on the new igniter where you want to cut them. Leave a little extra so you have wire at a length that is easier to work with. Scrape off 3/8 inch of insulation off the end of each wire and connect the wires with wire nuts. Re-mount igniter. Put drawer back in. Plug oven back in and try the oven. I hope it works. Mine did thanks to God. Take care.
To install I fi ... Read more rst unplugged oven (to prevent getting shocked) then took off the drawer on the bottom compartment (push in on tabs on rails until they release). Then take out two screws holding igniter. Mark wires with tape so you know which one goes to the upper part of the igniter and which one goes to the lower part. Then cut wires as close to the body of the igniter as you can so that you have plenty of wire to work with. Then hold igniter in about the place it will be mounted and mark the wires on the new igniter where you want to cut them. Leave a little extra so you have wire at a length that is easier to work with. Scrape off 3/8 inch of insulation off the end of each wire and connect the wires with wire nuts. Re-mount igniter. Put drawer back in. Plug oven back in and try the oven. I hope it works. Mine did thanks to God. Take care.
Read less
Was this helpful?
Thank you for voting!
Oven And Broiler Wouldn't Light
0 of 1 people
found this instruction helpful.
-
DENNIS from HERKIMER, NY
- Difficult
- More than 2 hours
-
Screw drivers
The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.
Was this helpful?
Thank you for voting!
oven whouldn't come on or if it did it whould take along time to come on and stop after awhile
0 of 1 people
found this instruction helpful.
-
Ralph from Garfield Hts., OH
- Really Easy
- 30 - 60 mins
-
Socket set
pulled bottom door out as far as you can. lift out broiler tray and the tray under that. to get the door completely out. on each side of the rail holding the door from come out push in the tap on each side and pull the door all the way out and off. reach inside and take out two nuts holding the old igniter and cut the two wires and remove
... Read more
it
stripe about 1/4 in of the wire. attache the wire from the new igniter. hold them two and use the white cap and twist it on the two wires and do the same to the other two wires. Bolt the igniter back on with the two bolts and your done. When you turn on the oven the igniter will click and turn on. it will be alot brighter then the old one and the oven will start pretty fast.
stripe about 1/4 in of the wire. attache the wire from the new igniter. hold them two and use the white cap and twist it on the two wires and do the same to the other two wires. Bolt the igniter back on with the two bolts and your done. When you turn on the oven the igniter will click and turn on. it will be alot brighter then the old one and the oven will start pretty fast.
Read less
Was this helpful?
Thank you for voting!