EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

32-01 - Instructions

All Instructions for the 32-01
76 - 90 of 234

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would not lite
1 person found this instruction helpful.
  • Walter from Danville, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver
First i removed the broiler door and then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and cut the two wires. I strip the ends ,connected the new unit with ceramic nuts that was provided an reconnected the unit. all was done in less than 30 min. EASY!!! plug the stove back in and WORKED PERFECTLY. note i receive the unit the same day it shipped....WOW
Was this helpful?
Thank you for voting!
oven would not light
2 of 4 people found this instruction helpful.
  • larry from 775, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
pulled drawer out and took old igniter off and replaced it
Was this helpful?
Thank you for voting!
Oven Would Not Light
1 person found this instruction helpful.
  • Michael from Houston, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.
Was this helpful?
Thank you for voting!
OVEN WOULD NOT COME ON
1 person found this instruction helpful.
  • david from SLIDELL, LA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.
Was this helpful?
Thank you for voting!
Oven would not light and gas would not come through.
1 person found this instruction helpful.
  • Jesse from Haines City, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I unplugged the stove then pulled the disconnected the wires that controled the igniter. I took the two screws off that held the igniter to the pilot port. I hand to cut the wires on the new igniter to some-what match the lenght of the broken igniter. Then I cut the connectors from the old part and used the fire resistant wire nutes tha t where included with the new igniter and connected it all. Put all the screws in tight, double checked every thing. Finally I plugged it in and it was working.
Was this helpful?
Thank you for voting!
the oven was slow to light and didn't reach the set temperature
1 of 2 people found this instruction helpful.
  • James from Chicago, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.
Was this helpful?
Thank you for voting!
Ignition not working
1 of 2 people found this instruction helpful.
  • Ricardo from Stamford, CT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Ins talled new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.
Was this helpful?
Thank you for voting!
Oven wouldn't heat , glow from bottom, and strong smell of gas
1 of 2 people found this instruction helpful.
  • Clayton from Gulf Breeze, FL
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers, Wrench set
First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two sc rews on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.
Was this helpful?
Thank you for voting!
Oven would not come on. If it did, it took a long time to heat up.
1 of 2 people found this instruction helpful.
  • Frank from Greenbackville, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed the broiler compartment door by depressing the slide stops inward and pulling the door off. Turned off the breaker to the oven. Used a nut driver to remove the old ignitor ( 2 screws ). Cut the wires off the old ignitor close to the porclin. Measured the new ignitor wires to match up with the old ignitor wires and cut them. St ripped 3/8 " off ends of newely cut wires of the ignitor and used the supplied wire nuts to secure them together. Replaced the new ignitor with the 2 screws. Turned on the oven and a cooking I went.
Was this helpful?
Thank you for voting!
Oven wouldn't come on
1 of 2 people found this instruction helpful.
  • Arthur L from Huntington, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.
Was this helpful?
Thank you for voting!
Broken hinge
2 of 5 people found this instruction helpful.
  • MICHAEL from MAY'S LANDING, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Replaced same very simple.
Was this helpful?
Thank you for voting!
The oven would not light and the house smelled like gas.
1 of 2 people found this instruction helpful.
  • Jeffrey from Mission Viejo, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I removed the oven floor and subfloor. I detached the old ignighter leaving the wires still attached. I then attached the new ignighter and fed each of the two new wires down through the bottom of the oven floor following the same path of the old wires which were still attached. I attached the new wires one at a time to make sure I connec ted them to the right place. Then, I pulled out the old igniter. I then attached the oven floors and turned the oven on which now works. The tough part is pulling the oven out from the wall to disconnect the power and turn off the gas. I did not remove the oven door.
Was this helpful?
Thank you for voting!
Igniter lights up, but no flame appears, no gas
1 of 3 people found this instruction helpful.
  • Denise from Clinton Township, MI
  • Really Easy
  • More than 2 hours
I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, w orked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,
Was this helpful?
Thank you for voting!
light bilb went out
2 of 6 people found this instruction helpful.
  • Denise from Landover, MD
  • Really Easy
  • Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people found this instruction helpful.
  • Christy from North East, PA
  • Really Easy
  • Less than 15 mins
It was pretty much a plug in. My husband had it done in a few minutes. I want to thank you for your great service with receiving the part.
The oven is working great and now I am back to baking.
Thanks for everything
Christy
Was this helpful?
Thank you for voting!
All Instructions for the 32-01
76 - 90 of 234