31JA Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Igniters were flaky on 2 burners and almost dead on 2
7 of 10 people
found this instruction helpful.
-
Matt from Craig, CO
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the uti
... Read more
lity drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Read less
Was this helpful?
Thank you for voting!
Electronic spark ignition would not ignite intermittently.
5 of 5 people
found this instruction helpful.
-
Charles from Old Bridge, NJ
- Easy
- 15 - 30 mins
-
Screw drivers
The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping th
... Read more
e new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.
Read less
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
no temp control
21 of 53 people
found this instruction helpful.
-
Cathreen from Lusby, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
very easy
Was this helpful?
Thank you for voting!
Gas manifold had holes in it.
5 of 6 people
found this instruction helpful.
-
Mr. J.C. from Haines City, FL
- Really Easy
- Less than 15 mins
Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.
Was this helpful?
Thank you for voting!
Igniter Switch on the burner was constantly on
8 of 15 people
found this instruction helpful.
-
Roman from West Caldwell, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
To get to the switch I had to remove the knobs and the front panel of the burner valves. There were some dozen screws, top and bottom holding the panel in-place.
The switch slid off the burner valve stem easily but removing the wires I had to pull with the pliers. There seamed not to be a wire release that I could see.
Replacin ... Read more g the wires was no problem. They slid into place by just pushing them in. Assembly was the reverse.
The switch slid off the burner valve stem easily but removing the wires I had to pull with the pliers. There seamed not to be a wire release that I could see.
Replacin ... Read more g the wires was no problem. They slid into place by just pushing them in. Assembly was the reverse.
Read less
Was this helpful?
Thank you for voting!
A high flame was coming out of the side of the burner
5 of 7 people
found this instruction helpful.
-
KAY from BRIDGEPORT, CT
- Really Easy
- Less than 15 mins
Easy......pulled out the old one easily and popped in the new one.......saved a lot of money...no repair bill for either diagnostic fee or assembly fee ...No mark up for the part either. Very happy mom!
Other Parts Used:
Was this helpful?
Thank you for voting!
Timer know would no longer set the time...
5 of 7 people
found this instruction helpful.
-
Rachael from Adams, MA
- Very Difficult
- More than 2 hours
-
Screw drivers
I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the swit
... Read more
ch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.
Read less
Was this helpful?
Thank you for voting!
The oven igniter lit up but the valve wouldn't release the gas to ignite.
4 of 4 people
found this instruction helpful.
-
John from Wisconsin Rapids, WI
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured wi
... Read more
th the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
Read less
Was this helpful?
Thank you for voting!
oven would not turn on flame
6 of 10 people
found this instruction helpful.
-
Michael from Secaucus, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment.
... Read more
Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
Read less
Was this helpful?
Thank you for voting!
Panel light burnt out after 10 years
4 of 5 people
found this instruction helpful.
-
Pamela from La Junta, CO
- Really Easy
- Less than 15 mins
I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just
... Read more
4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .
Read less
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people
found this instruction helpful.
-
peter from marine city, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f
... Read more
ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Read less
Was this helpful?
Thank you for voting!
Oven and burners wouldn't light
3 of 3 people
found this instruction helpful.
-
Kory from Collingswood, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Easy repair. I removed the module housing at the back of the stove (two screws) and slipped the wires off the old spark module (I had to use pliers to gently pull one or two wires off--it's an old stove). The existing wires slipped right on the new module. I did have to use the mounting adapter that came with the kit, but that was the
... Read more
fiddliest part of the whole repair. It took me longer to move the stove out and back than it did to do the repair.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat.
3 of 3 people
found this instruction helpful.
-
Thomas from La Crescenta, CA
- Easy
- Less than 15 mins
-
Nutdriver
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pus
... Read more
hed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat/ turn on
3 of 3 people
found this instruction helpful.
-
Diane from NEW HAVEN, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first
... Read more
turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
Read less
Was this helpful?
Thank you for voting!