31JA Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven stopped while the wife was cooking.
15 of 18 people
found this instruction helpful.
-
Marsha from Concord, MA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws hol ... Read more ding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws hol ... Read more ding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!
Read less
Was this helpful?
Thank you for voting!
Light Bulb burned out
12 of 12 people
found this instruction helpful.
-
Jeffrey from Marietta, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. Th ... Read more e order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. Th ... Read more e order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.
Read less
Was this helpful?
Thank you for voting!
Rubber gasket failed due to age
14 of 18 people
found this instruction helpful.
-
Mary from Woodland, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
I learned that I could clean the window in the oven door. In taking it apart I saw that the gasket had fallen into the oven door. I found the part online, it arrived in three days. I removed the metal part of the door, removed what was left of the old gasket and put in the new one. Put the metal part of the door back on, and it was as g
... Read more
ood as new.
Read less
Was this helpful?
Thank you for voting!
leak
12 of 14 people
found this instruction helpful.
-
George from Plainville, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
removed then installed new unit by hand. received order the next day-am. delivery time great.
Was this helpful?
Thank you for voting!
spring broke on one side of door hinge
14 of 20 people
found this instruction helpful.
-
Travis from Lexington, OK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.
Was this helpful?
Thank you for voting!
oven won't stay light
10 of 10 people
found this instruction helpful.
-
Shannon from Lake Park, IA
- Easy
- 15 - 30 mins
-
Screw drivers
removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.
Was this helpful?
Thank you for voting!
Oven would not lite
11 of 14 people
found this instruction helpful.
-
Timothy from Petaluma, CA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
With a little adjustment to the mount the part went in ok. Checked the oven works like new; well better than new.
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 8 people
found this instruction helpful.
-
Treasure from High Point, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
Read less
Was this helpful?
Thank you for voting!
Purchased home but stove had no broiler pan.
16 of 33 people
found this instruction helpful.
-
Raymond from BLOOMINGTON, MN
- Very Easy
- Less than 15 mins
Purchased 2 piece broiler pan from this site
Was this helpful?
Thank you for voting!
the burner knobs broke off
10 of 17 people
found this instruction helpful.
-
Belinda from Downey, CA
- Really Easy
- Less than 15 mins
I put the 2 burner knobs on and now I have 4 working burners....Thanks for the quick delivery....
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 11 people
found this instruction helpful.
-
John from Caliente, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Parts came very quickly from PartSelect. Good service.
Was this helpful?
Thank you for voting!
Door Spring Broke
7 of 9 people
found this instruction helpful.
-
Thomas from Van Nuys, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.
Was this helpful?
Thank you for voting!
30 year old gas stove needed a new burner assembly.
6 of 7 people
found this instruction helpful.
-
Caroline from South Windsor, CT
- Really Easy
- Less than 15 mins
We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!
Was this helpful?
Thank you for voting!
spark ignition in stove failed to turn on burnes.
7 of 10 people
found this instruction helpful.
-
David from Upland, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical.
... Read more
I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Read less
Was this helpful?
Thank you for voting!
Burners would not ignite
6 of 7 people
found this instruction helpful.
-
Charles from Kalamazoo, MI
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed cover from igniter, took off wires, replaced wires on new one, secured in place, put cover back on.
Was this helpful?
Thank you for voting!