31GG Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
On/off sputter of stove. Ignitor/glow bar problem.
0 of 1 people
found this instruction helpful.
-
Anthony from Camillus, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.
Was this helpful?
Thank you for voting!
oven would not work, broiler and range did work.
0 of 1 people
found this instruction helpful.
-
Richard from Farmington Hills, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags.
... Read more
However I did pull up and remove oven door for complete access to oven.
Rick,
Detroit, MI.
Rick,
Detroit, MI.
Read less
Was this helpful?
Thank you for voting!
oven didnt light
0 of 1 people
found this instruction helpful.
-
mitch from brooklyn park, MN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
i removed old part, then installed new one. easy
Was this helpful?
Thank you for voting!
Front Burners
0 of 1 people
found this instruction helpful.
-
collins from Freeport, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.
Was this helpful?
Thank you for voting!
failed igniter
0 of 1 people
found this instruction helpful.
-
David from Easton, PA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter
... Read more
by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.
Read less
Was this helpful?
Thank you for voting!
My Gas Oven Wasn't Lighting and it Scared Me!
0 of 1 people
found this instruction helpful.
-
Kim from Cedar River, MI
- Easy
- 15 - 30 mins
-
Screw drivers
I was worried over the fact that my oven was filling up with propane but taking a long time to light. One day it didn't light for over ten minutes. I shut it off and put the still frozen pizza back in the freezer. That's it, I thought. I'm not going to use the oven again until it's fixed.
I looked online and ordered the part. ... Read more It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.
I baked several batches of Christmas cookies and three coffee cakes the next day.
I looked online and ordered the part. ... Read more It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.
I baked several batches of Christmas cookies and three coffee cakes the next day.
Read less
Was this helpful?
Thank you for voting!
Oven Was Dead
0 of 1 people
found this instruction helpful.
-
IRIS from BROOKLYN, NY
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out. First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is hel
... Read more
d on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle. Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I would like to now say something about the excellent service received from parts select. They have an excellent user friendly site & I received my part the next day.
Read less
Was this helpful?
Thank you for voting!
ignitor would heat enough to open gas vavle to lite oven
0 of 1 people
found this instruction helpful.
-
Jon from Mayville, NY
- Really Easy
- 15 - 30 mins
-
Socket set
unplugged the oven, unplugged the ignitor and removed the two screws
Was this helpful?
Thank you for voting!
Lower burner failed to light, broiler running fine
0 of 1 people
found this instruction helpful.
-
Christian from Washington, DC
- Really Easy
- Less than 15 mins
-
Screw drivers
Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Suc
... Read more
h a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."
Read less
Was this helpful?
Thank you for voting!
oven wouldn't get hot
0 of 1 people
found this instruction helpful.
-
scott from newtown, CT
- Really Easy
- Less than 15 mins
-
Nutdriver
well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation ar
... Read more
ound wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't light.
0 of 1 people
found this instruction helpful.
-
Roberta from Los Angeles, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.
Was this helpful?
Thank you for voting!
Gas valve would not open
0 of 1 people
found this instruction helpful.
-
Frankie from Carlsbad, CA
- Easy
- Less than 15 mins
-
Screw drivers
I was afraid I would have to remove the built in oven from the wall to do the repair but it was simple. I pulled on the wire a bit and the connector popped out of the hole in the back. After that it was as simple as removing 2 screws, replacing the unit, plugging it in and pushing the new connection out the hole in the back. They include
... Read more
d a piece of insulation with the kit that I then forced into the hole to protect the new plug from the heat of the oven.
Much easier than I thought it was going to be. In about 10 minutes I had the oven working again.
Much easier than I thought it was going to be. In about 10 minutes I had the oven working again.
Read less
Was this helpful?
Thank you for voting!
oven ignighter would glow, but oven would not work
0 of 1 people
found this instruction helpful.
-
graham from littleton, MA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
I removed the two screws holding the ignighter on, pulled it a few inches, disconnected the plug, plugged the new ignighter in, tightened the two screws, turned on the power, and it worked. 1,2,3.
Was this helpful?
Thank you for voting!
Oven would'nt preheat
0 of 1 people
found this instruction helpful.
-
Ray from Valhalla, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Pulled out the plug, pulled out the stove, removed the oven door, pulled out the lower shelf and racks. Used a nutdriver to remove the 2 screws from the bracket, disconnected the old ignitor, new ignitor was an exact replacement, put back in the screws, pushed back the stove and plugged it back in....Was back in business in a matter of s
... Read more
econds!!
Read less
Was this helpful?
Thank you for voting!
oven light burnt out
3 of 10 people
found this instruction helpful.
-
William from Schwenksville, PA
- Easy
- Less than 15 mins
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this helpful?
Thank you for voting!