31GG Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Screws in the old unit were frozen and stripped
0 of 1 people
found this instruction helpful.
-
Lee from Cave Junction, OR
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
During removal of the original ignitor the screws would not come out. they were rusted. using some liquid wrenchI tried to remove them again and they broke. Using an angle drill and special bits I was able to drill out the screws. I re- tapped the holes and the repair was simple. My wiring required additional insulation over the supplied
... Read more
wiring that came with the new ignitor. Cut the wires about 1 1/2 inches from the plug and added the insulation then replaced the plug with the provided wire nuts. Mounted the new unit and all tested perfectly. Closed up oven and operates perfect as if new.
Read less
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people
found this instruction helpful.
-
joan from florissant, MO
- Easy
- 15 - 30 mins
-
Screw drivers
My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.
Was this helpful?
Thank you for voting!
Oven would not light, but igniter would glow.
0 of 1 people
found this instruction helpful.
-
Roger from Greenwood, AR
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.
Was this helpful?
Thank you for voting!
The oven would not light even though the glow plug lit.
0 of 1 people
found this instruction helpful.
-
HELMUT from MIDDLE VILLAGE, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
The oven worked like a charm again.
Was this helpful?
Thank you for voting!
The oven gas valve would not turn on
0 of 1 people
found this instruction helpful.
-
Steve from Prospect Heights, IL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Replaced the oven ignitor. Toughest part was removing old screws.
Was this helpful?
Thank you for voting!
Oven quit lighting
0 of 1 people
found this instruction helpful.
-
MIKE from Phelan, CA
- Easy
- 15 - 30 mins
-
Nutdriver
I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for
... Read more
years because I didn't realize how easy the fix was.
Read less
Was this helpful?
Thank you for voting!
very slow heating, smell of gas
0 of 1 people
found this instruction helpful.
-
Carole from Girdwood, AK
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this helpful?
Thank you for voting!
Things cooked in the oven were taking longer than usual to be done.
0 of 1 people
found this instruction helpful.
-
Ron from Belleville, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the ignit
... Read more
er came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat to temp and could smell gas.
0 of 1 people
found this instruction helpful.
-
Christopher from Dearborn, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Was this helpful?
Thank you for voting!
thermostat temprature bulb hanger clips
1 of 4 people
found this instruction helpful.
-
Dwayne from Atlanta, GA
- Really Easy
- Less than 15 mins
snaped them into oven cavity attached temp bulb job complete
Was this helpful?
Thank you for voting!
Light burned out in upper oven
0 of 1 people
found this instruction helpful.
-
Shirley from Las Vegas, NV
- Really Easy
- Less than 15 mins
Screwed in light bulb and glass protector
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people
found this instruction helpful.
-
peggy ann from forest city, NC
- Really Easy
- Less than 15 mins
very easy
Was this helpful?
Thank you for voting!
gas would go on and off -- oven slow to heat
0 of 1 people
found this instruction helpful.
-
Stephen from Evanston, IL
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers
Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perha
... Read more
ps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!
Read less
Was this helpful?
Thank you for voting!
Oven burner would night ignite
0 of 1 people
found this instruction helpful.
-
Douglas from Hanover Park, IL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Replaced the ceramic glow ignitor by removeing the two screws holding it to the mounting bracket. Gas and electric were tturned off. Unplugged the ignitor from rear of oven. Installed new switch in the same way and if worked perfect. Part was ordered online for $48. I saved one hundred dollars by doing it myself. My outdoor grill was hard
... Read more
er than this.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
0 of 1 people
found this instruction helpful.
-
Dennis from East Grand Rapids, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
After unplugging the oven from the wall, I removed the grates and floor of the oven, and the thing that spreads the flame out. Needless to say, I'm no repairman! Next I simply unplugged and unscrewed the old element and screwed and plugged the new one in. Replaced the floor, grates, and flame thing in, and we were back in business! It was
... Read more
a very easy fix, and Partselect.com was a pleasure to research and do business with! I would certainly recommend this site to others.
Read less
Was this helpful?
Thank you for voting!