316E740F352 (1652670 -1996) MTD Snow Blower - Parts

This genuine drive belt is an original replacement part sourced directly from the manufacturer and is commonly used in Craftsman lawn mowers and edgers. Made from flexible rubber, it transfers power from the engine to the pulley that drives the cutting blades. Over time, the belt may become brittle or cracked due to wear and exposure, req...Read moreuiring replacement to maintain optimal performance. Measuring 3L x 35.80 inches, this belt is sold individually. A wrench may be needed for installation, depending on your equipment model.

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This is a shear bolt, also known as a snap-off bolt. This is a fastener designed to break under a specific amount of pressure and protect the machine it is installed on from that excessive load. In lawn equipment, the shear bolts typically connect the auger or blade to the drive shaft. Therefore, if the bolt snaps, the auger gets jammed a...Read morend cannot rotate so that it will not damage the rest of the unit. This bolt has a diameter of 5/16 inches, with 18 threads per inch, and is 1.5 inches long. To remove the shear bolt from your machine, you need to turn the power off first. With pliers or a wrench, grip onto the broken end of the bolt and twist it gently out of its hole. If it is stuck, you may need to coat the bolt with a penetrating oil or tap the bolt out with a mallet. Since this authentic OEM part is sold individually, refer to your instruction manual so that you can purchase the correct number of bolts for your machine.

This chute flange keeper is sourced from the original equipment manufacturer for use in snowblowers. The plastic keeper allows the snowblower chute to pivot, and secures the flange that connects the chute to the blower frame and holds it in place during use. Over time the flange keeper can break or fall off, which causes the chute to disl...Read moreodge or shift from its position. If you notice that debris is discharged in the wrong direction, and you have difficulties adjusting the chute then this is a sign that the flange keeper is no longer functioning as it should. Clean the chute flange and surrounding area before placing the new keeper on. Use a pair of pliers to align the the holes on the flange keeper with the holes on the chute and lock it in place.

This Slide Shoe is rated as "Easy" to install and requires a wrench set. It is a manufacturer-approved part that comes in black and is constructed of metal. The part is used to help the snowblower slide smoothly and is attached on the side of the augur housing. If missing or broken, it should be replaced.

This is an authentic OEM sourced replacement part designed for use with snow throwers/blowers. It allows you to engage and disengage the unit. This cable is sold individually. You may need pliers to complete this repair. • Remove the cable end from the control head and install the new one • Now you can run the new cable down to the ...Read morecontrol handle • Attach the other end of the cable • Tie the cable in place just as the old one was, but leave enough clearance and free play to avoid over-bending and breaking the new cable

This is an authentic OEM part for Craftsman lawn and garden equipment. This bushing has an internal diameter of 0.380", is made of durable black plastic, is not part of an assembly or kit, and is sold individually. The purpose of this bushing is to ensure there is a tight fit between parts. A common sign this part needs to be replaced i...Read mores if you notice any parts loosely connected or detached. This part will become worn through regular use of the machine. It is located in various areas, depending on your model. Refer to your owner's manual for the exact location. You will need a wrench and pliers to complete this repair. Customers rate this repair as Medium difficulty.

Used mainly in snow blowers, this flange bearing is typically installed on the axle and creates a tight fit with little friction while still allowing for movement.?Your equipment will likely feature multiple of these bearings, so refer to any diagrams for your model to determine whether you will need one, or more. This is an OEM part that...Read more is sold as an individual item and has a 0.75-inch inner-diameter, 1-inch outer-diameter, and 1-inch height.

This item has been sourced from the original manufacturer to be used with snowblowers from MTD, Ryobi, Yard Machines, Bolens, and Yard-Man. This item is the hard rubber tire that fits onto the friction wheel and is used to rotate the friction disc. Overtime this item can wear down and need to be replaced to make good contact with the friction disc. This item is available as an individual replacement part.

This is a worm gear that is designed for use within a variety of snowblowers and snowblower tractor attachments. The worm gear is used to rotate the auger through the drive mechanism, also known as the transmission. Featuring an approximately 2-inch diameter, this worm gear is made of high-quality, durable metal and is sold as an individu...Read moreal part. The worm gear will likely be secured in place using bolt or other fastener, and replacing this gear will require a wrench set and screwdriver. Make sure to check any user manuals or diagrams for exact placement of the worm gear within your snowblower.